Hello, I am working with a nRF54L15 and using a TF-M build (cpuapp_ns). SDK and toolchain are currently v3.0.2. NRF_SECURTY is enabled (by default) and here's the relevant...
Hi,
I’m working on a Matter application using the nRF Connect SDK v2.9.2 . I’ve added the AirQuality cluster into my device with sub-sensors: CO₂, PM1, PM10, TVOC, and Temperature...
I would like to do a FOTA using bluetooth and external flash memory on nrf52840 board. I am also using sdk 2.9.1 The issue i am currently facing is I get the below when i...
Hello nordic community,
i have custom board that have nRF5340 and nRF7002, our requirement is to use wifi every 5 minutes (connect send data and disconnect) but randomly...
Hello everyone,
As the title suggests, we're trying to get the on board flash (mx25r64 as far as I can tell) of the nrf7002dk devboard working as a USB mass storage device...
Hi! We're testing nRF7002 with the nRF7002-DK and NCS v3.0.2. CONFIG_NET_ZPERF=y has been added to the nrf/samples/wifi/shell/prj.conf, the rest is untouched. Running that...
I am using the nrf5340 on a nrf7002fk dev kit. I am interested in low power operation so I am measuring the power consumed.
I am running a simple app:
int main(void) ...
Hi,
Are there any reference design for interfacing a nRF51822 with an external sensor for e.g. an accelerometer (STM LIS3DH, AD ADXL362 etc)
Also do we have a profile...
My application would like to receieve notifications at several different times before a radio notification event. Specifically the application needs to receive notification...
Hello,
i have two operation modes:
One or more devices are bonded and advertising mode with whitelist (BLE_GAP_ADV_FP_FILTER_CONNREQ)
A new proximity central device...
Hi all,
From this forum and the examples given in the "sdk" find two approaches to measuring the battery voltage:
using external divider 10M/2.2M+22nF
using integrated...
In the previous discussion you told me to buy Mod nRF-8001 from olimex and i was also very optimist after going through its design that it can easily be connected to Arduino...
I have an application in which I would like to be able to enable and disable the SoftDevice.
But there are peripherals (Application Timers, Two Wire Interface, etc) that...
Hi,
I'm using PCA10001 connect to a sensor chip.I would like to set the register values for sensor chip as SPI master role and I need to switch to slave role to read the...
Hello,
i just want setup 1Tx and 1 RX using NRF24L01+ chips. but i am confused what should be Transmitter side Tx & Rx and what should be in Rx Tx & RX ? in order to use...
Hi,
There were similar questions already anwsered but none of them work for me. So the situation is as follows. When i program the chip though SWD interface the chip probably...
Hi,
Regarding the source found in "Nordic/Source/ble*" etc (downloaded as part of the nrf518xx SDK
[*] How can I find out which revision/release-tag I'm using. Would...
My design may not connect to a client for most of its operational life but will need to be in advertizing mode whenever not connected. I want to specifiy the advertizing interval...
The nRF Utility app for Android does not support the Galaxy Note 3 yet. Probably because the phone has only been released for a few days so far.
Please add support for...
Hi all,
I am a new user to the BLE technology and to the Nordic's development tools/chips.
I use the nRF51822 development kit and the nRFgo Starter kit to develop a BLE...
In my current project, I have to develop a board with 2 mcu:
nRF51822
STM32F2/F4
The nRF51822 should running S110 SoftDevice and act as a kind of »over the air«...
