I have a USB host capable Android device running CentOS via Linux Deploy and everything is working perfectly except i'm unable to connect to my USB nRF24LU1+ Crazyradio PA...
Hi,
I am using multiperipheral mode in ble_app_hrs using the ble_app_multiperipheral example taking the functions on_connected and on_disconnected while connect and disconnect...
Hi,
I'm using nRF52810 on SDKv14.2 and I have changed the bootloader from 52832 to work for 52810. I could do OTA now. I found that the bootloader there is no timeout when...
Is there a way around the issue where bluetooth communication acting as a pass-though terminates the packet whenever null character is found in the packet.
SDK: nRF5_SDK_12...
Hi,
When creating and adding an characteristic to service, what the meaning and difference between these two variables:
attr_char_value.init_len
attr_char_value.max_len...
Hi all,
I have compiled the ble_app_hids_keyboard example for a nRF52832 on a Laird DVK-BL652 breakout board.
I have a tablet running android 5.1.1 and the nordic nRFConnect...
Hello All,
We are using nrf52840 board interface with wiznet550i.
We try to implement mqtt tls 1.2.we get following errors..
I get certificate verification error -0x2700...
Hi,
We are looking for an industrial solution to program our NRF52832 on a custom board, until now we are using the programming chip directly from the NRF52DK, it works...
My custom board with NRF52810 is done and I'm now trying to get some examples working. I am adapting blinky_s132 in SES. To do this I edited the project options including...
i'm new to this board can you find some course for this board
from scratch the courses will be very helpful
just the video tutorials are very advanced
the documentations...
Hi folks,
I am working on ble_app_uart example program nRF52 SDK 15.2 Verion , in this case i am writing the data in flash for future use , Now i am to get the specific...
Hi Team,
We are using nRF52840 DK with sensors. We developed a custom code that is working fine. But the issue is current consumption. Showing below the readings.
The...
I have taken the code found here:
https://github.com/bjornspockeli/custom_ble_service_example
and modified it so that the custom characteristic is located in user memory...
Hi,
Good day!
I tried to add the RTC2 driver to our application and i keep getting this compiler error message (using sdk16.0).
Here is my sdk_config.h. Not sure why...
Hi
I'm planning to connect three different BLE peripheral like Heart-rate sensors, Health Thermometer, and Blood Pressure to a Central BLE device.
I'm using a small customized...
Hello
What is the specified max current on the supply pins for nRF52840?
The GPIO pins are specified to source max 14mA in 'high drive' mode:
How many of these pins...
Got called back to an old product that used nRF24LE1. Need to do a simple hot fix.
But I don't have the nRF6700 Dev Kit with me anymore. It cost almost $600 to get one from...
To the kind attention of Nordic support team,
I know that gazell secured libraries are available at least for keil compiler and nRF52840 device.
Are those libraries available...
Hi,
We are seeing a voltage of approx 1 volt on our USB connector when USB is not being used (VBUS).
We are using our device in a Wet environment; this voltage between...
Hello,
I am using nrf52840DK and I try to send data from sensor to ble toolbox. I want it to advertise for 1 minute and then go sleep for 5 minutes and do it again and again...
Hello dear Nordic Semiconductor. I use one of your creation - nRF52840 USB dongle. I have troubles with using USB CDC ACM. I add ble stack to gather info about advertisement...
Hello,
I want to do fast advertising (100ms) (LE privacy enabled) for about a minute, then I want to transition to slow (1000ms) advertising forever (or until a connection...
