There is the board mark on the chip like n51822CEAAD01350A0, where DO is Build code, 1350 is tracking code(YYMM), A0 is lot code.
My question is how can I get those codes...
I'm trying to debug a randomly occuring Hardfault. In trying to trace down the source I read the CPU registers use the Nordic hardfault_implementation.c which grabs the register...
Dear nordic employee
my purpose is send a data the length is from 150 to 273
when my server device send data by sd_ble_gatts_hvx（the send length is fixed 10 bytes） ...
Dear nordic employee：
The service I want to find is the sound service of the thing52 thingy sound service
I tried to modify the HRT_central_client project to find the...
When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
I've recently discovered the power consumption issue with FreeRTOS and SDK12.3:
devzone.nordicsemi.com/.../
So, I am now using SDK12.3 with SDK13.1 FreeRTOS files.
...
I am using Nordic SDK to program an nRF51822 chip. I want to optimize power consumption as much as possible so I am looking at using the -march gcc flag. The problem is I...
I am using the ble_peripheral template that comes in Nordic SDK 8.1. I setup uart logging and also debugging with the following lines of code:
void assert_nrf_callback...
Hi, We are trying to connect a LED to one of the GPIO of nRF52840, we would like to know how to connect it. Connect it such that the nRF52 GPIO sink current or source current...
Hey, I am using WT51822-S4AT module and want the nrf51822 to connect to phone. I don't have nrf51-dk. I am using stm32f0-discovery kit. Can it be done using that kit? I searched...
Seems battery reads are not consistent in thngy52 2.1.0 software.
Observed a ~4% difference in the consequent battery reads. This difference is high (upto ~40%) if the thingy...
In the recent past, I used a SoC in which GPIOs could be configured as "open drain", that is in which there is an internal transistor where the SOURCE is grounded, the DRAIN...
Hey,
I'm using nRF as a SPI slave with a Raspberry Pi. I'm seeing that even at ~3MHz SPI frequency, my first byte transferred gets corrupted. I have a test setup where...
I am using nrf52 with s132 and armgcc
As I add functionality to the code I get to a stage where it fails. Linker runs OK but the result fails to execute.
The observable...
I am currently working on a BLE beacon project on nRF51822. Using SDK 12.3.0 and s130. The device has to advertise URL, advertising name and output power level. And these...
I am trying to control a current measurement chip (DDC114) that works with a protocol that is close (enough) to SPI. It has 2 channels, s.t. it can be read out and integrating...
I am attempting to run my first bit of code on my Nordic nRF52-DK and every time I have attempted to upload the code to the board, the board disconnects in the middle of the...
Hi, I'm using nRF52832, SDK13.0.0 as peripheral.
My iPhone app(my company's) makes connection without problem.
But Android app gets connection fail when it tries to connect...
