This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
Sorry ,I have the problem with increasing the max data length(more then 20 bytes) in the characteristic , I change the att_mtu size like the value in the picture, but after...
I have developed a beacon application which transmits the required data from an analog device. I want one more application which scans the transmitted information from the...
Hi,
I am using nRF52840 dongle for my development with "usbd_ble_uart" profile from SDK located in this following path RF5_SDK_15.2.0_9412b96\nRF5_SDK_15.3.0_59ac345\examples...
Hi.
I saw lots of questions but I could't find answer about BLE & flash write func.
Setup is nrf52832, S332, SDK 15.3.0.
using ble, ant+, gpio, timer, adc,
in code...
Hi Nordic:
I have a question about retart saadc. i want to restart saadc in a bsp event(BSP_EVENT_KEY_3) and it works. the following is my code:
i learned in this forum...
1. Download and install nRF Connect from Google Play or App Store. 2. Open nRF Connect. 3. Make sure that the DK is running the ble_app_uart example. LED1 should be blinking...
Hi,
My firmware is working well and handling required functions, so I have begun trying to work on power management to reduce device power draw. I am using S140 and my BLE...
Hello,
Using light switch dimmable (experimental) example, I will like to change the default name displayed by the server/client to a custom name.
See the screenshot below...
Hi,
I'm trying to receive data from a UART transceiver. I'm using a nRF52 DK with a RS485 to UART transceiver chip.
On my debug session I get the " NRF_SERIAL_EVENT_DRV_ERR...
Hi,
I have a nRF52833 DK which contains PCA10100 debugger on it.
However, examples in the nRF5SDK160098a08e2 SDK seems like not supporting PCA10100.
Which example...
Hi all, I am beginner to Bluetooth module interface and I am in the stage of implementing the software for Bluetooth module to start and visible to other Bluetooth device...
Hi,
Lookin at this ticket https://devzone.nordicsemi.com/f/nordic-q-a/32090/qspi-pin-mux-on-nrf52840 for the nrf52840 it is said that it is ok to put QSPI on any pins (depending...
Hi,
I need to use cJson library to parse some json data. I have seen that the library is located at "nrf\ext\cjson" path. I have also seen how to add that library to a...
The documentation is VERY difficult to search. A search only goes over the chapter. I get different results depending upon which one I am in .... aarrg! And there are SOOO...
