hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hello,
This is the first time I try to implement DFU to update my simple application OAT via BLE on the nRF51 DK.
My simple application is a simple peripheral which...
I have a GPS over UART to a nrf5283. For debugging the GPS, I'd like to passthrough UART from my PC to the GPS. I know the nrf5283 only has one UART. Is there a simple way...
First about my setup: custom devices with NRF52832 chips (SoftDevice 132 v.4.0.2), android smartphones Nexus 5x and 6p.
I'm trying to connect as many BLE devices (peripherals...
I'm working on a custom board with an nRF52382 connected to an IMU over I2C. The IMU provides 2 separate interrupt signals, and I would like to route each of them to a separate...
Hello,
Today I've a strange behavior of nRF51 DK (everything was working ok until today, the last things I did was to reset the J-link FW after a total erase of the board...
Hi all,
My configuration:
nrf52832 microcontroller
Softdevice S132 V4.0.2
Nordic SDK 13.0
I'm using an "app_timer" in repeated mode with 10Hz frequency...
I have recently acquired a NAND chip from Micron and would like to use it for storage.
However, looking through the datasheet I found out that the addressing scheme require...
I'm planning using nRF52810 for a new product to reduce the power consumption.
But i worried whether old smartphone with Bluetooth4.0, like Iphone5s can connect with equipment...
I am dealing with the nRF24L01 to develop a remote controller. When I read the specification, I found a specification item, called C/ICO, with a typical value of 12dB in the...
hello,
I'm trying to send long (73B) data on a given characteristic using Android client as the central.
I well received:
USER_MEM_REQUEST OK
> #define...
Hi to everyone!
I'm following this guide to learn how to use secure DFU on a nRF52832DK board.
All steps have been done successfully, or I think so, until I reach the...
I want to find the agent of China, please, thanks
About Bluetooth and 2.4G, nRF52840/nRF52832/nRF52810
(The agent can provide some technical support and sales)
Can someone please explain the below line mentioned in NRF5 Serial port abstraction layer documentation.
Do not use synchronous API (timeout_ms
parameter > 0) in IRQ...
Hi there,
I want to flash nrf51 firmware from another MCU which is connected to nrf51 with UART interface.
I have seen dual bank serial bootloader examples, in that firmware...
