Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Does the Antenna in this Beacon relates with this "BAL-NRF02D3 '50 ohm balun transformer for 2.45GHz ISM"? Any idea what's this "BAL-NRF02D3" for? many thanks!
Hello,
I've got a nrf52840 DK and Adafruit nrf52840 Express (less complicated then DK) i'm trying to run a PWM example from datasheet (46 PWM — Pulse width modulation...
Hello Nordic Team
I am working on SDK-v15.3. I have a requirement to update the DFU firmware in lower version too but this SDK version doesn't supporting to update lower...
i am working on a wearable device and want to develop a 1inch wearable using nrf528232 can anyone help e with minimum pcb design requirement for programming.
thanks
I am setting up the DFU example based on NRF52832.
I tried with different version of SDKs (SDK13, SDK15 and SDK16) and all based on armgcc. All toolchains are the same version...
Dear Sir,
I have implemented a program and tested it using BMD-300 Rigado DK.
The program will advertise continuously and I used nRFConnect to connect to the peripheral...
Hi, I would like to capture all bluetooth packets on a specific channel, and get their access code. Same as what Ubertooth does. Is it possible using the nRF52832? If not...
Hi,
I am trying to follow the OpenThread tutorial to build the nRF52840 NCP:
https://codelabs.developers.google.com/codelabs/openthread-hardware/#3
I installed the...
I have successfully completed my bachelor thesis project on a simple wireless sensor network using 3 nRF52 nodes and RPi with using Mqtt and Ble-6LoWPAN example from SDK....
Hi All,
We use nRF52 BLE Sniffer.Its working fiine. Please letus know, weather its possible to sniff multiple BLE devices at a time using single Sniffer. If possible, let...
Will there be an official implementation from nordic of the generic mesh models as described in the mesh model specification or are you counting on each developer to make...
How to change the Bluetooth Mesh broadcast address?
Use the sd_ble_gap_addr_set function to change the broadcast address of PB-GATT ， But PB-ADV still hasn't changed.
...
We are implementing a DFU controller in a microcontroller that communicates with the nRF boot-loader over serial. The target device is nRF52832 using SDKv15.3.0. The boot...
Hello.
I want to see NRF_LOG_DEBUG ("some") through the terminal. When I compile, I get the following error: What should I set or change? MCU : nRF52840 compiler: IAR...
1.I used Nrf52810 and the flash size is 192KB. I now need Master mode and slave mode. The SoftDevice I chose is S132 (S112 slave mode only). I found that S132 (130KB) + Bootloader...
Hi.
I have issue measure ADC value from battery.
setup is NRF52832, SDK 15.3.0, S332, using ANT+, BLE, GPIOTE, PPI, RTC, APPTIMER, LOW_PWM
my goal is measure periodically...
