Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Does the Antenna in this Beacon relates with this "BAL-NRF02D3 '50 ohm balun transformer for 2.45GHz ISM"? Any idea what's this "BAL-NRF02D3" for? many thanks!
Hi,
I'm trying to port my project from SDk12.1 to SDK14.0, I've got everything working fine except the DFU process. The main issue is that we've got some devices distributed...
Hello,
I am designing a custom board with NRF52832 IC. I followed all PCB consideration suggested by Nordic.
This blog suggests, If using a PCB antenna, the matching network...
This question is similar to this thread:
devzone.nordicsemi.com/.../
However it was framed differently and didn't really clear anything up for me.
Say my application...
Hello,
I have an application that has to be ported to the newer Softdevice version. I've already ported my application to the SDK 13 and tested it with the new Softdevice...
The NVMC documentation states the CPU is halted while the NVMC is writing or erasing flash. If the CPU is halted, then interrupts shouldn't need to be disabled during flash...
blog.bluetooth.com/management-of-devices-bluetooth-mesh-network
The Provisioning Protocol
During provisioning, the Provisioner and the Device to be provisioned communicate...
as this screenshots show, i add some headers to nRF_Libraries, and add the directory of the folder nRF_Libraries to Options for targets /c++/include paths,but after building...
Hi,
I am trying to use the SAADC via ble when noridc is connecting with other device and adding value to advartasing. This is my code but i've got some problems.
1)...
I am modifying the bootloader_secure_ble code to receive a serial number via BLE and store it in flash. However, whenever I call nrf_dfu_flash_store or nrf_dfu_flash_erase...
Hi,
We are currently working on one project.
Initially, the nRF52840 & S140 (v5.0.0-2) & SDK14.0
examples \ ble_central \ ble_app_multilink_central Based on the example...
Hi Team,
I am using sdk12.2.2 and nrf52. I want to use one gpio to detect button state & have to operation on that event.
I used one method to configure(code snippet...
Following the guide found at : file:///C:/Github/STIWHN/SDK_thingy52/thingy_sdk_v2.1.0/documentation/firmware_compile.html#compile_gcc
I still getting errors trying to...
Hello,
For the softdevice update, is it the responsibility of the bootloader to make sure, that the softdevice was copied correctly?
If for example the bootloader calls...
Hi,
When i use FreeRTOS tasks with priorities 2,3,4,5 what i need to #define for XXX_CONFIG_IRQ_PRIORITY of SPI,SAADC and GPIOTE at the file sdk_config.h
Thanks
Hello, I use nrf51822 , sdk 8.0.0, s110
I defined advertise interval and timeout
#define APP_ADV_INTERVAL 320
#define APP_ADV_TIMEOUT_IN_SECONDS 3
Also, I write...
