Hello,
I am writing an iOS code using Swift3 to connect an iOS10 device to nRF52 pca10040 and blink an LED. The nRFConnect on iOS can easily connect using the device name...
void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
Hello,
There's an interest on the LTE-MTC module.
I can see it's based on nRF9160.
I'd like to inquire about the MTC technology please, does this module support CATM2...
Hi,
I'm using a buffer size of 64 bytes using function
nrf_drv_uart_rx(&app_uart_inst, rx_buffer, 64);
When I receive only one byte packet from the remote, I get EVENT_RXDRDY...
i want to use pwm of rnf52810.but i don't know how to recognize what pins is pwm.
what pins in 52810 i can use wire to connect and then use it's pwm function?
or i can...
Hello, I try to import big project from Keil to SES. The main idea is to move to better IDE and use the same compiler ARMCC provided by Keil (license is present).
I have...
I am trying to using ceedling with FFF to create mocks of some of the NRFX HAL files. However, when I run ceedling I get some very weird errors. I've taken the `test/include...
Hello,
Below are details of my setup:
Peripheral: nRF52 DK
Central: One Plus 5 android phone
Sniffer hardware: nRF52 DK
Wireshark version 2.4.2
On Wireshark, I...
Hello everyone,
Some info about my setup: OS: Windows 10 IDE: SEGGER Embedded Studio v4.22 (64bit) HW: nRF52840 Dongle rev 1.2.0 as Coordinator, nRF52840 DK rev 1.1.0 as...
Hi,
I am trying to implement OOB pairing via USB. I have the USB portion sorted out. The idea is for a peripheral device to send over OOB data over this medium, which then...
I have problem with send hex on flash memory in dongle. I erase fllash than plug out dongle i know that i shuldn't but raspberry sey, he can't erase falsh. Dongle has 1.8V...
Hello,
can you please advise if the GPS antenna for the dev kit nRF9160-DK would also be available separately?
Our customer received this kit with version 0.8, which does...
Since APIs have changed as new nRF5 SDKs have released from time to time, it is not clear how custom service can be implemented on BLE peripheral for nRF52840 (pca10056) S140...
Hello All
I try to port the blinki example (with softdevice s130 2.0.1) to my Hardware with the nrf51822_xxAA.
The application will run without Softdevice.
But as soon...
Stack violation: stack pointer outside stack area.
Cause: Data bus error (PC value stacked for the exception return points to the instruction that caused the fault).Bus...
Hi,
I have PCA10000 Revision 0.9.0 nRF9160 Board with external antenna (Molex 206640)
I try to make GPS work. Here is my step:
I compiled GPS under samples ..\root\ncs...
I followed the start up procedure-
All OK, but my nRF9160DK doesn't connect to the network.
Only led3 is blinking.
I think iBasis-eSIM is not enabled in my area.
I...
