void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
Hi,
I am working with the BLE Nano module and the mbed online compiler. I have the Nano acting as an SPI slave. The problem occurs when I try to add BLE functionality....
I've spent some time searching and haven't found a definitive answer or anything obvious in the code. I'm developing the firmware for my application on the nRF52 DK, which...
Hello nordicers,
I'm stucked with long writes (android central to nrf52 peripheral)
I'm using SDK 12.3 and S132 v300. Android as the client central (RxAndroidBle libary...
Hello,
I ported nordic heart rate example to nuttx. I have peer_manager_init() in my codes.
After programming the device, I can connect and bond when I issue "nrfjprog...
main.c I'm using S120 softdevice with nrf51822, I want to use S120 as central and peripheral devices.
When I received my beacon data then switch to peripheral for advertise...
Hi!
nRF52, SDK13, S132.
I work in central mode and need make
ble_nus_c_rx_notif_enable()
But in the code drivers I only have tx function. In a SDK9 for nRF51 I...
Hello,
I'm trying to prototype an application on the nRf52 DK (PCA10040) using the GCC toolchain. I followed all of the tutorial for setting things up and I can build and...
Hi all,
I tried to load the DFU example for nrf51822 from SDK12.3 on the dongle(PCA10000).
softdevice: S130 2.0.1
I followed the tutorial on: devzone.nordicsemi.com...
What I am trying to accomplish is to establish a connection between an iPhone (device 1) and an NRF52 (device 2), then sniff the data sent between them from a third device...
Hello,
I have designed a custom board with NRF52832 IC which controls vibration motors. And I am turing on vibration motor from n-channel mosfet as shown in the image below...
Hello ,
I'm using ble_app_eddystone example and I would like to stop the advertising and TLM when I press button 2. I able to create a correctly inicialization of button...
we validate the example /ble_centeral/ble_app_multilink_central with NRF_SDH_BLE_TOTAL_LINK_COUNT equals 8. Change the number from 8 up to 15, it still work.
but when the...
in a ble_nus_c_evt_handler().
SDK13, nRF52, S132.
I made connect success. When it done, I send command to peripherial to start discovery. When event came
case BLE_NUS_C_EVT_DISCOVERY_COMPLETE...
Hi, when trying to read a register from a chip using the IIC interface,blocking mode:
uint32_t ms5837_cmd_read(uint8_t *data, uint8_t length, uint8_t register_address)...
