Ok so here is the issue. I was trying to build a simple application which is described in the tutorial for characters. After building an advertisement and understanding the...
I was working with IAR and SDK10.0 before. For some reason I have to transfer my project to Keil and SDK9.0. My program worked well for the old settings. While keeps got NRF_ERROR_SOC_NVIC_INTERRUPT_NOT_AVAILABLE...
Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Hi all,
I am trying to deploy the long range mode in nRF58240 DK. I modified the Blinky example in SDK 16.0.0.
It just keeps reseting and the code error is 0x0007. Is...
Hi. We are using the USB CDC example to send data to a windows PC over virtual comport.
First question is that in the sdk_config.h file NRFX_UART_DEFAULT_CONFIG_BAUDRATE...
Hi Nordic Team,
Please suggest logic to scan all peripheral devices by the central device.
In my BLE project when I'm trying to scan all peripheral devices which are advertising...
Hi Nordic Team,
In a BLE project we need to configure same device to conditionally act as central (to scan) device and peripheral(to advertise) device based on the state...
If I write to the MWU REGIONENCLR register and immediately access memory that was previously watch enabled an event is still generated. If I delay a small amount (tested with...
Hello,
we have made our fist device with a custom Service with 5 characteristics. And now we have a strange problem which I was not able to debug to find a solution.
We...
Hello,
if I call this code all works:
if I call following code only ZB_ZCL_ON_OFF_SEND_ON_REQ take effect on target
I'm simply swap the call order, where's the error...
Good morning everyone,
I saw this question asked a few times, but no conversation was actually fixing the issue.
I am developing a product where I want the pairing to...
This seems to have changed in recent SDKs, so that none of the examples or techniques mentioned in previous posts is relevant any more.
I am using the SDK v16.0.0 ble_app_blinky_c_pca10040_s132...
When I carefully follow the instructions at https://infocenter.nordicsemi.com/topic/sdk_tz_v4.0.0/thread_ot_libraries_building.html , I am missing some of the openthread libraries...
Hello.
I just started using nRF52840-DK board with SEGGER Embedded Studio and I'm trying to use it to save data in a micro SD through an adapter. I tested it with the Fatfs...
SDK15, nRF52832, S132
I notice that after about 30-50 bond and delete cycles peripherial to central, central doesn't want to bond. Before it bond and after that delete bond...
Hi there, I am working on controlling the nRF Mesh device (nRF52840-DK) via the bluez version of 5.52 (meshctl). I try to connect to Nordic nRF52840-DK (example <nrf5_SDK_for_Mesh_3...
Good morning,
Is it always required to use Segger J-Link in order to flash Bootloader, Softdevice and Application to a new device?
Could you summarize the different possibilities...
