Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
[uart - Copy.rar](/a master _error.png ttachment/3cc01f5e2484d2b0f33e62befd3e6a62)
hello there
I am interfacing master nrf51 dk with nxp's slave lpc11u24
(1) my main...
It is good practice to prefix the includes from one's C libraries with a directory so that they are all part of the same 'include namespace'. Unfortunately the Nordic SDK...
Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hello,
I've been trying to program my nrf52832 board with an st link v2 dongle or an st32 disco board with no luck with eclipse(Didn't find a dedicated tut for using all...
Hello
i am using the nrf52840 with sdk 13.
on the client side i saw you are catching the cccd_handle. for the heart rate characteristic.
basically i am leaning the basic...
Hi all, is it possible to use NRF51-DK for Master Control Panel?
I dont have NRF51 dongle so I was thinking if there is a way to make NRF51-DK work with MCP.
Hi,
I have the following situation:
1 central connects and bonds to 2 peripherals. All the above 3 devices are power cycled.
Now, the central need to remember the...
My system's data rate is 16MHz.it input to nRF52832 is parallel 8 bits. Is it possible? I want input the data to RAM by easyDMA,please to tell me how to do it ? thanks!
Hello,
A stupid newbie question: APP_UART_FIFO_INIT seems to get stuck while trying to run
example code.
Only modification I have made is the usage of SEGGER_RTT for...
I am working in sdk14 nrf52832 ble_app_hids_keyboard_pca10040_s132.
I set the .allow_repairing flag to true :
static void pm_evt_handler(pm_evt_t
const * p_evt) {...
My system's extend IC need a 16MHz clock ,because the nRF52832 work in 64MHz,so I want to use nRF52832 to generating a 16MHz clock output to a GPIO pin .please tell me ,how...
Hi,
I'm using nRF52832 and nRF52840 to work with MCU, then we should do the firmware update by the uart. I have compiled the bootloader_secure_serial project in the SDK...
I have ordered two "nRF51822 Bluetooth Smart Beacon Kit"s on this page:
www.nordicsemi.com/.../nRF51822-Bluetooth-Smart-Beacon-Kit , and got these two:
I've downloaded...
Am building a HID Mouse device, starting with the nRF52-DK as hardware target and the BLE peripheral HID mouse sample app. Builds, loads and runs, apparently fine (i.e., can...
Hello,
I am trying to add an extra service like "experimental_ble_app_blinky" into "ble_app_hids_keyboard" example code. "ble_app_hids_keyboard" example code has 3 servcies...
Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
i am using uart of nrf52832. the SDK is nRF5_SDK_12.3.0_d7731ad. the uart is app_uart .when i was testing the uart sending and receing .i find that the uart is stoping where...
