It is good practice to prefix the includes from one's C libraries with a directory so that they are all part of the same 'include namespace'. Unfortunately the Nordic SDK...
Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
I'm in the process of updating from SDK13 to SDK14. In the new CLI, there are a lot of NRF_CLI_VT100_CMD's that are used which weren't there before. If someone is using a...
Worked out of the box. The next day it would not turn ON. Tried charging with and without power switch ON. Charged from an Apple iphone brick and also from a computer USB...
Hi everyone,
I have moved from the cable connection firmware upgrade to the OTA-DFU using the nRF52 dev kit. I am able to download the firmware from nordic's website and...
51822/S130/SDK v12
I was testing prepared Write from iOS to 51822. Write Req/CMD can succeed, but Prepared Write failed with 'Unknown error code 0x82'.
What this 0x82...
I am design a very compact board for my project and running out of space. For this I am planning to replace two DCDC inductors with a single one. Is it possible to do this...
I am communicating with the nrf8001 via SPI, from an HCS08 MCU. First thing I receive:
0x01 0x04 0x81 0x02 0x00 0x02
This makes sense, it tells me it is in setup state...
In my design I am planning to power up some sensors from nRF52832 GPIOs. Is it possible to maintain the GPIO state high during the low power mode of MCU?
Please guide here...
Hello,
I have been testing the BLE multilink examples for the s120 softdevice. More specifically, I have tested the ble_app_hrs_c example in the experimental s120 folder...
Is it possible to configure the parameters of the advertising library (eg. SDK v12.3.0 using SD130 v2.0.1) so that my peripheral device (eg. nRF51) changes after a limited...
I've configured peripheral for broadcast, but why can't IPHONE search it? I don't need APP development. I just want the phone to show it. Is there any special requirement...
Hi,
I was considering the following scenario and didn't find an answer. Could you please help?
Assumption:
There in a BLE peripheral (e.g. nRF52) and central ...
Im using sdk 14.0 and s132 When i add flashwrite codes to my project which has bluetooth communication ,it does not work I wanna send data to flash and i wanna read/write...
I do not want to use SoftDevice, I want to write new application from application to Code Area(0x00 - 0x80000).
Can I use fds without using SoftDevice?
Also, Is there...
Hello,
I am using SDK 12.2.0 with s130_nrf51_2.0.1 softdevice and running ble_app_hrs example.
My FLASH and RAM settings are:
FLASH (rx) : ORIGIN = 0x1b000, LENGTH...
Hello,
I am using sdk12.2.2 and pca10040. I want that my beacon advertises continuously for 10 sec and then it stops advertising for 5 secs. Do I need to use rtc for this...
