Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
In case the DSM metadata is changed compared to what is stored on flash, the 4.0.0 code is supposed to clear the flash from any configuration but this doesn't work properly...
Hello,
I'm pretty new to rtos and totally new to nordic's nRF9160. I've been trying to get this working all day and can't really seem to figure it out based on the resources...
Hello,
We are using nRF52840 with SDK 15.2.0, a bootloader, the bootloader settings and the SoftDevice. Our product has a cellular modem to be able to perform OTA firmware...
Let say a situation where I want to know if the just connected client is the same as the one that was last disconnected, but if the client uses RPA than have somehow to try...
Hello,
I'm developing a BLE device based on nRF52832 and SoftDevice 112 using SDK 15.3.0. The device operates only in peripheral mode with only a single connection to the...
Hi
I try to run BLE HRS collector example.
when I run the project, in RTT terminal I have these error
00> sd_ble_enable: app_ram_base should be adjusted to 0x20001CD8...
Hi,
We are evaluating devkit nRF52840-DK using SDK nRF5_SDK_16.0.0_98a08e2.
The application development is ongoing, based on examples\ble_central , using which we are...
Hi,
I have a multilink NUS central that connects to several NUS Peripherals using SDK 16.0, S140 (NRF52840 REV1). Currently I'm testing with only one peripheral, sending...
We're using the nRF52840 in our product.
We require to perform continuous scanning, with little power usage as possible.
We've seen in the Nordic specs and verified with...
Hi,
I'm using NRF52840, and I've developed a feature which bonds with NRF toolbox application. The problem is that when I'm using secured BLE, I can't receive any messages...
Hi,
I have an issue with getting a GPS fix from time to time under the almost same conditions. When it did not get a fix I could see in the UART log that the nRF9160 was...
Our custom board has an nRF52832. In our custom build system the application HEX and SoftDevice HEX are merged together into a single HEX file, this is achieved by Nordic...
We are in the process of getting our product through SRRC certification in China. I am using the radio_test example from SDK 11.0 for this. All is working fine.
However...
I downloaded SDK v16.0 and in the examples, I can't seem to find the dual_bank_ant_s332 folder.
It is present in SDK v14.2.0 in this path
...\nRF5_SDK_14.2.0_17b948a\examples...
