I am using nrf sniffer for trouble shooting. But it always exit unexpectedly. Wireshark was still open but the DOS window got closed.
I am attaching the log.txt.
log...
Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hello! I am testing project "ble_nfc_pairing_reference". When my NFC device touch the NFC antenna on the device screen is written: pairing; connecting; could not connect....
Hello,
I have an nRF52 DK, running S132, as a client. After scanning and connecting, I use ble_db_discovery_start, which finds the devices of interest, connects, and finds...
As the title specifies, on writing to the registers mentioned, I receive a Fatal error.
Here's the test code
void save_ram()
{
__DSB();
NRF_POWER->RAM[0].POWERSET...
Hi,
I would like to know if anyone ever tried to alter the SEGGER J-Link OB Code that goes on the ATSAM3U2CA-AU IC (this is the IC that controls de PCA10040).
I'm asking...
Dear support,
I am working on some custom boards embedding the nRF52832-CIAA chip using SDK-v11.0 and s132-v2.0.1.
I have got 9 custom units and out of them only 4 work...
I asked about if NRF52 can pair to eachother without a PN532, but sounds like no, it can only read RFID tags.
So, how about if at factory we make RFID sticker/tag that...
Hi,
I need 32 bit timer-counter with s130 stack. Timer0 is 32 bits, but ble stack uses this timer. So how can i use timer1 or timer2 like 32 bit timer?
Is there any...
Do u have mobile/ios application that allows you to scan for Bluetooth low energy devices with nRF52840 and communicate with them?
If not, how we can do it?
Hi,
I am wondering which is the best method for BLE security to avoid MITM, protect the data (sniffers) and limit connection only to allowed devices for a massive number...
I am now using nrf51822 chip connected to a 50-ohm nominal input/conjugate match balun and then connected to an Embedded antenna.
I am requested to do a radio test which...
Hi,
In my project, I only have PCBs with nrf51822 chips and do not have a plan to buy a spectrum analyzer yet. But the certification requires me to apply DTM application...
The overall goal and then the specifics of what's been tried: I'm trying to utilize as much of the left-over flash space as possible to store environmental data during periods...
Hello,
I started working on mesh networking and to initiate i am looking at lighting control example . I have one nrf52dk PCA10040 which can be used as client and two nrf51...
I am working through link this tutorial and I've been able to successfully complete the steps up to D3. I'm using the bootloader_secure_ble example from SDK13 on an nRF52840...
