Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
I'm planning to use one of those beacon platforms:
www.ebay.com/.../352167746226
www.ebay.com/.../112493464451
for a close proximity positioning system now I'd like...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
Building for a PCA10040 dev board (nrf52832) in SDK 14.0.0 with the S132SD v5.0.0
I'm an encountering an issue where calls to printf() are only displaying a single byte...
Most application examples which use the scheduler have a main loop looking something like this,
int main(void)
{
// Initialization <snipped>
// Enter main loop...
Hi,
"wait" hangs when running the mbed blinky example, build in develop or release, on nrf52840.
The program is flashed with a J-Link and the program runs OK at first...
Dear support,
I am working on some custom boards embedding the nRF52832-CIAA chip using SDK-v11.0 and s132-v2.0.1.
I have got 9 custom units and out of them only 1 cannot...
We have ordered nRF52840 development kit . In windows xp comp port is coming as 8 but the device status in general is this evice cannot start.(code 10). Same in windows 7...
Hi,
I am working on ble_app_uart_c central code provided in sdk12.3.0 with softdevice s130.I added pwm code provided in peripheral examples in ble_app_uart_c central code...
Hi all,
I wanted to know the default values for the different NRF Radio paramateres in the ble_uart example.
I want to make some tests but not sure what is set as default...
Hello sir,
we have completely develop product using nRF52832 and S132, sdk13.1, and its great working fine with BLE. But for same application we want to use wifi module...
For my audio application, I need to convert pcm out from pdm module(nrf52832) to an audio format (mp3,wav) continuously. Is there any method or procedure for this??...or any...
This may be intentional, or an oversight but the
uint32_t app_gpiote_user_register(app_gpiote_user_id_t
* p_user_id, uint32_t const * p_pins_low_to_high_mask, uint32_t...
Dear All,
I am starter for nRF52832 DK. Could you please tell me where the start point is and where I can find demo programs ?
Thank you so much.
Best regards,
...
