Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
Hi,
I am using SDK v14.1 for nRF52840.
The secure_dfu_usb debug example works well when the J-link RTT Viewer is connected.
But when the RTT Viewer is disconnected the...
Hi everyone,
I would like to know if it is possible to establish a serial communication to a PCA10028 card using Adafruit Bluefruilt LE friend knowing that there is no...
Hello everyone,
I am using nrf51822 chip that has functionality to flash bl, sd or app using mobile app application. I want to reuse this functionality in order to have...
When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
I am using the ble_app_uart example as my base on a 52832 with sdk 12. My project runs off line power and needs to remain available for connection 24/7. I have commented out...
I am communicating with a temperature sensor (MLX90614), which has flag register. However, in order to read this register, I must send a read sequence without issuing the...
Hi,
As has been mentioned many times, the DIF on both the nRF51 and nRF52 consumes quite a bit of current. In the past, on the nRF51, I've relied on power cycling both chipsets...
Hello,
I would like to make changes in ble_app_uart_c example for connecting to a custom peripheral.
Service Uuid of my peripheral is as follows : 99aa0001-d0e3-44ce-a306...
Our homeowners association has a gate which opens when a transmitter in the car is pushed. I would like to add a BLE device to the gate which would trigger the gate to open...
Hello all,
So.... i'm quite green to the Nordic and Bluetooth protocol.
i want to program NRF51422.
what i have now it the Nordic test board and a spi-canbus print. this...
With custom hardware and softdevice flashed on board (using BDM_350) when I try to debug I get and error: with () at 0xfffffff9
It appears to come from address 0x3a2
...
I currently have a Braveridge device which uses an advertising rate of 50 Hz (connection interval is 20ms)
CONNECTABLE_ADV_INTERVAL is set to 0x0020
sd_ble_gap_adv_start...
Hi, I am trying to determine if there is an error in the generated code or if I am not performing the actions correctly. I am trying to Update Characteristic User Description...
Hello,
when a bootloader wants to update the softdevice, I think it has to first store the SD binary somewhere in flash memory and then to use sd_mbr_command to ask the...
I'm trying to debug the Experimental IEEE 802.15.4 example on a nRF52840-Preview DK Board PC10056 with IAR Embedded Workbench ARM 7.70. Compiling and linking the project is...
