How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
I am in the process of porting my code from SDK13.0 to 14.0 in order to use s332 v5.0
I can compile and run my application. While it's running, I can see that it is sending...
We are using this device and we seem to have an issue reading from P0.20.
I know this is a dual purpose pin. We have programmed it for input with pullup. We have it attached...
I am currently porting my project from SDK13.0 to 14.0 so I can use s332 v5.0.0.
I receive warnings when compiling
.\_build\nrf52_firmware.axf: Warning: L6330W: Undefined...
I would like to know if it's possible to pair two NRF52832 together using NFC. NOT an android phone to an NRF52, but a central NRF52 standalone connect to a peripheral NRF52...
Hello,
I am using nrf52832 with SDK12 with gcc compiler. I have extended the ble_app_template example with 2 services.
I have 1 timer interrupt using RTC(100 ms) and...
I've been noticing lately when running debugging on my code, a few minutes in it loses connection and says No Source Available for "0x01e054". I'm sure how to even figure...
I am trying to debug a custom version of the bootloader_secure_ble example but am running into FLASH space issues. The bootloader app does not fit into FLASH with -Og optimization...
Hello,
I am using Keil IDE for a while,and it is working perfect so far until, my code size gets bigger than 32K, I also decided to try GCC. I noticed GCC code size for identical...
nRF52832
SDK14.0
Hi,
I had two questions regarding Fstorage:
The Fstorage module works by having a queue of NVM operations. This queue only holds two types...
Hello!
I am using the nRF52832 with nRF5_SDK 14.0.0. with a JLink connection. My OS is Ubuntu 16.04.
After placing NRF_LOG_INFO() statements around my code, connecting...
Hi,
I am working on an application that needs to use pairing/bonding. I am incorporating peer manager into the project. I have included in Makefile paths the following...
I'm a little confused here...I have a basic main function which is turning on/off some GPIO and logging through SEGGER_RTT.
I thought that in order for that to work, you...
Hi,
I'm trying to get SPI working with an accelerometer (LIS3DH). I'm currently trying to use the nrf_drv_spi_transfer() function. See code snippets below.
// Initialize...
SDK14.0.0
nRF52832
s132
I would like to DFU the contents of the App Data section. In particular, I would like to erase the contents for a "factory reset" command.
...
I am setting up the DFU example to compile in Clion using ARMGCC 4.9 2015q3 and cmake. Everything compiled as it should and the DFU advertises. However, when trying to do...
