We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
do you have a user gide for Serial DFU just like buttonless DFU ,like this link https://devzone.nordicsemi.com/nordic/nordic-blog/b/blog/posts/getting-started-with-nordics...
Hi,
I have flashed lte_ble_gateway on nRf9160 DK (PCA10090) and hci_uart on nRF52840 SoC.
After flashing, I am getting some random RSSI values and MAC Address , instead...
Hello,
I have two micro-controllers communicating over SPI.
The STM32F746 is SPI master. The nRF52840 is SPI slave. I use SDK v15.3.
I am sending two bytes over SPI...
Hi.
I had to unpair from the Android Bluetooth list by doing pm_peers_delete () when bonding. It's ok. I know why it should. But sometimes I can't find my paired device...
To the kind attention of Nordic support team,
We are very interested indeed in using your nRF52840 and nRF52810 devices in our projects. We also would like to use your gazell...
Hi,
I have used nRF52832 with my Python code succesfully many days. Suddenly it stopped to working and gives me an error message: NordicSemiException: Failed to ble_gap_scan_start...
Hellou. I'm developing application, which is modifiaction of light switch demo. I need use 128 servers and one client. But when I redefine in SERVER_COUNT to 128 in client...
Hi all, ( nRF52 DK, SDK 15.3, S132 )
Many asking about how to add 2 "service data" in the GAP advertising, but no real answer on the solution !
The first service data...
Hey everybody!
I'm trying to implement the following use case.
Android device connects to nRF52, bonding occurs, android device is put into nRF52 whitelist, after this...
Hello, I am trying to combine light switch client example with fds functionality.
For these I did next steps:
Included all ‘c’ files from the fds example to the light...
I notice that the USB Serial (the lowest numbered COM port of the three, that's connected to the Cortex-M33) isn't opened in a Serial Terminal before the application starts...
Hello:
When I try to use mesh, I found that the bootloader never work in low power mode. If I only program application into the nrf52832, the power consumption of its low...
Hello.
I m working with mesh demo: https://github.com/NordicPlayground/thingy52-mesh-provisioning-demo
In Android app we can press "identify" and after that Thingy's led...
Hi, On a button press I need to enter to disconnect from the currently connected device and then start advertising in order to allow a new device to connect. I manage to disconnect...
