At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
I am building an ap (based on peripheral: ble_ap_uart with custom characteristics.
I want 18 characteristics for a single service.
My software works with up to 12 characteristics...
Hello, we would like to consider this chip for a product, but I have been waiting for this to be on sale for purchase since February 2017. It's still 12 weeks out and it's...
Hi, I followed the NRF51 Guide and downloaded the file linked, and it installed the J- Link Commander, once opened it gives a prompt J-Link> and when I enter in -e command...
Hi guys,
I’m using nrf51822, s130 and sdk 12.3.0…
I would like to achieve that unknown peripheral won’t find my product or at least differentiate by device name while...
Can i use the bouder router used in thread example(on nrf52840) in the iot example to replace the Rpi bouder router so i can skip the tunnel setup(using hurricane tunnel)...
Hi everyone,
I have some questions regarding the use of EDIV and Rand in BLE Legacy Pairing.
What I understood from the specs is that these are generated during...
I think instead of releasing separate SDK for #BluetoothMesh, Nordic Semiconductor should merge #BluetoothMesh into #SoftDevice. Is it possible ?
If yes, then we can even...
We are using the nrf52840 with OPENTHREAD and would like to use the Nordic COAP application because block transfer and observe are implemented. We need to do multicast and...
Hi,
I have a development board nRF52832 and we are looking for 3rd party modules built on the same. I want some configuration changes on the modules.So, please someone help...
Hi
I am currently using SDK 12.1.0 with SD 3.0.0.
I want to add the option for serial DFU, which was added in SDK 13.0.0.
I wonder if I can implement the serial bootloader...
first of all many many thanks for nrf sniffer 2.0 and all of it's improvements (linux, live data display, easy install ... etc)
i'm sure there are still a lot details missing...
I am trying to use the nRF Connect v1.0 RC with the pca10040 board. I followed the instructions of your [page] and when i open the serial port i got an error (Error occurred...
I am using nrf52832_xxaa with SDK v11.0.I tried writing into the APPROTECT register by using the code below
sd_softdevice_disable();
NRF_NVMC->CONFIG = (NVMC_CONFIG_WEN_Wen...
Hi, as per subject, I would like to know the trade-offs of using the internal DCDC vs LDO when it comes to RX sensitivity specific to the nRF52840-QIAABB variant.
From this...
Hello,
I am using the nRF840 PDK for testing the radio communication.
During my tests, for TXPOWER=0xD8(at minimum), I found a gap of 7 dBm between the radio output...
