We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
Hi, to use the bluetooth 5 long range feature, do both the transmitter and receiver need to be configured to in this mode to work? Do you have any example AES 128 that I can...
SDK： nRF5_SDK_11.0.0
Softdevice： s132_nrf52_2.0.0_softdevice
project：examples\ble_peripheral\ble_app_hids_mouse\pca10040\s132\arm4
I have some questions about bonding...
Hallo,
I try to port some existing BLE application from SDK 12.2 to SDK 14 that used the S132 Softdevice.
With 12.2 it was possible to configure bandwidth requirments...
Would it be possible to use BLE for a sensor network with aprox. 40 battery peripherals measuring a float at 100hz? 50hz? For one central unit, or how many if needed.. The...
Hi,
One of my pca10040 stays on bootloader mode.
I have tryed copying J-Link OB-SAM3U128-V2-NordicSemi 160212.bin file on the bootloader drive but it stays the same. ...
Hi Everyone,
I just purchased an nRF52840 PDK and I am trying to program it via nRFgo. I erased the flash, selected the latest s140_nrf52840_5.0.0-3.alpha_softdevice.hex...
Hello,
My team and I are experiencing a problem with our custom DFU Bootloader, which is based on the Experimental Bootloader Secure Serial example (SDK 13), running in...
Hi,
My SDK version is 13.0 and my problem is when I run the examples\ble_peripheral\experimental_ble_app_buttonless_dfu project the 52DK seems ok but when I use the DFU in...
Hello:
I am setting up my nRF52840 development board to work with the S140 softdevice on Segger Embedded Studio; however, I am running into issues with the flash_placement...
Hello,
I've seen some conversations around the forum for applications that must share the same ID. My application must share SPIMO and TWIMO (ID 3, base addresss 0x40003000...
Hello,
I want to make beacon with my uuids. I am referring to code ble_app_beacon code from sdk 12.2.2
I have made changes according to my requirements in my code.
I am...
Hi, we downloaded the latest version of the sniffer 1.0.1 (today).
We tried that but we could not get it to work reliably?
The application sees the device, we select and...
I am using the nrf51822 with a latching circuit as shown controlled by P0.05 pin.
I am using the following code SDK 10.0 S110 softdevice to Power ON the circuit (PowerPin...
