Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi
Is there an example in the SDK or anywhere that displays the use of LE Advert Extensions? I have been browsing softdevice v6.0.0-6.alpha and I came across the structure...
Hi all !!!
I understand Output OOB, Input OOB.
I case of No OOB, value which is attached to Confirmation value is 0x00, what happens in case of static OOB?
Hi there~~ I'm trying to create a voice streaming application with the Mesh and the Nordic Thingy:52 I downloaded both the nRF5 SDK 14.2 & Mesk v1.0 to test the Mesh's light_switch...
Hi everyone,
Currently, my team is developing a BLE keyboard which uses 6KRO protocol. Are there any examples for the 6KRO protocol using nRF52 chips?
Thanks!
Update:
Hi again to everyone!
After a while, I've received a new custom board and a new cable to connect through P19. But everything are not working again.
Now, in...
I have a 12 MHz voltage controlled oscillator driving the nRF9E5 at pin xc1 and xc2 is open will this pose a problem for running the nRF9E5? The clock has a +-50ppm stability...
I am working on a project that requires me to wirelessly communicate with and program a left hand Oculus Touch controller, since dismantling it will cause damage. The controller...
I see I have more than 100 free pages (~ 101 KB) on Nrf51822 with SD130 but how can I assign all of them to the FDS module. I am going to manage a database with FDS on the...
Hello,
I am trying to use PCA10000 dongle with the pb-ble-driver-py libraries with absolutely no success, as I get a "Failed to open. Error code: 13" error.
I am running...
Hi, please!
The question is related to "nRF24L01P_Product_Specification_1_0.pdf" datasheet in " www.nordicsemi.com/.../nRF24L01P_Product_Specification_1_0.pdf" and to NRF24L01P...
Hello. Engineers.
I'm a beginner in nRF52832, I'm looking for someone who can help me.
I have nRF52832 development kit. I tried examples blankly with SDK14.0.
It working...
Hi,
I've recently come across a problem where in some cases my device's memory gets trashed.
Ideally I'd be able to set a watchpoint on a memory location so that I could...
main.c
I am working in sdk14.1 nrf52832 ble_app_uart_pca10040_s132 and ble_app_uart_c_pca10040_s132.
ble_app_uart_pca10040_s132:
nrf_ble_gatt_att_mtu_periph_set(&m_gatt...
