I ran the ble_aci_Tranport_layer_Verification.ino sketch from the Nordic BLE library and I get no output to the serial monitor after "nRF8001 Reset Done" is displayed. I think...
I am trying to debug my code today and am finding that Eclipse is constantly breaking execution at the INLINE function app_timer_evt_get(). I do not have any break point set...
Hi,
Recently,
the DFU of the "Master Control Panel" (Android) can not complete the upload mission.
But,
the DFU of the nRF-Toolbox in iOS is
work well.
Old...
I just tried out the new iOS nRF Toolbox 1.5 and it doesn't seem to handle long init packets.
I gave it a zip file that contains a 137216 byte 'application.bin' and a 192...
Hello everybody,
In the SD_EVT_IRQn ISR I check for BLE and SoC events and set flags for each so my application can fetch and dispatch the events in the main context. ...
Hi, in the example bootloader in sdk 7.2, there is an assembly code block in SVC_Handler, in dfu_ble_svc.c.
I found that the offset in line:
LDR R0, [R1, #24]
always...
In nRF51 SDK 7.1.0, there is a c header file using c++ keywords operator .
Here is a snippet of components/ble/ble_racp/ble_racp.h using the keywords.
/**@brief Record...
I would like to start off by saying I am not a very experienced programmer and I only have base knowledge of Java and Android Studio. Furthermore, I have no experience in...
when I run the secure bootloader example in nrf51422 development board, the code is working fine. I am able to load the packet through nrf toolbox app. But the same code when...
hello
i am using nrf 52840 board with sdk 13.
i use heart rate collector example to connect the 6 heart rate peripheral .
Modified the hrc_c example following this link...
I want to monitor NRF radio channell's RSSI to switch on "free" channel.
How to make it properly?
This is my code:
if(rx_q_flag == true){
err_code = esb_init(RX,...
I want to increase the MTU values to increase the throughput from my own service (currently based on NUS service) and to receive the data with pc-ble-driver-python with the...
I am using power_manage function to keep low power sleep mode. And I used below peripherals in code,
SPI master, SPI master is disabling when ever I am not using.
...
It appears to me that some of the saadc APIs (e.g. those found in nrf_drv_saadc.h in SDK 1.4.0) are missing in the nrf SDK for HomeKit.
Some hint where to find these functions...
How do you do
The attachment is a problem in the previous code, please help to debug it, thanks ble_app_uart_pwm.rar
E:\nordic\nRF5_SDK_12.2.0\examples\ble_peripheral\ble_app_uart_pwm...
Hello.
There is an executable file built by setting the address of the entry point (RO_Base) to 0x00000000 with Keil's linker setting.
I converted this executable file...
Hi,
I'm using nrf52840 with openThread. I like set the MCU in system on low power mode. RTC1 is used as application timer for wake up and start transmission periodicly. For...
Hello,
I could not find any related info, so I would like to ask few questions:
I have pca10028 board, using s110, sdk 6, ble_app_uart code. The board gets connected...
Hello all,
During current measurements of our product using nrf52832QFAAB0 I've noticed a high IDLE current of ~450uA. Trying to isolate the problem we programmed our board...
I am working on adding DFU, persistent storage and pair/bond feature to an existing nRF51 application, developed with SDK v10.0.0 running on SoftDevice S110 v8.0.0.
I looked...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Hello,
I used translation software.
I am transferring test data from nRF52832.
I want to down the average current consumption in data transfer.
I am currently...
