Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
Hello guys,
I wan`t to make an project that send trough serial port a new image to flash my nrf9160.
By the moment I managed to send and recieve data but only on uart0...
Hi,
Iam running the BLE uart and zigbee light multi protocol example. Using the latest thread and zigbee SDK v3.2.0. The example is quite good. That the door(zigbee+BLE...
Hello,
Where do I find the plating material information for the following part numbers? is it Matte Tin?
Nordic Semiconductor nRF51822-QFAB-T
Nordic Semiconductor...
I design a 4 layer pcb which include nrf52832. But i'm unsure what rf trace width should be on 4 layers pcb?
This trace 30mil width and 5mil clearance for 2 layers pcb as...
Hi,
I am using NRF52. i have custom board on that external flash and SD card is not available. i want to use msc class so that i can drag and drop file and read it in controller...
Suddenly my app, running on iOS 7, is reporting lots of spontaneous disconnects by the peripheral device, an nRF51822, indicating a timeout:
didDisconnectPeripheral: Peripheral...
Hi !
I added " Read Characteristic" in NUS.
How can I get different values every time I click "read again"? For example, read the value of a varying ADC from here. ...
I am investigating increasing throughput in our application. Upon investigation both with our software and the ble_app_att_mtu_throughput example code. I found that there...
Hello! I want to develop such a functional: nrf52840 receives a line from my application that it saves to memory, and then, when I click on the button, it returns this line...
Peripheral: nrf52832
Central: nrf52840
The communication speed after executing sd_ble_gap_conn_param_update is different in the following two cases.
case 1:
...
Hello
I am trying to do BLE communication using nRF52832. I wrote the exact same program on a module (BLENano2) with the same nRF52832 chip, but one was able to do BLE...
Hi.
- Is it the case that before every write to persistent storage via nrf_fstorage_write, the page written to has to be erased first (via nrf_fstorage_erase) since only...
I have used nrf51Dk with nrfPPK before some days now trying to flash nrf51DK but its not detecting any board I tried to recover but not recovering it I have already added...
Hello,
I am using nRF52840, SDK_16.0.0, S140 SoftDevice and Segger 4.16 for flashing the image.
1) For Secure Serial bootloader in below path, I want to change Tx...
