The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I have a nRF52840 dongle.
My understanding is that the nRF52840 has an on-chip regulator (Vdd out) that can be set from 1.8 to 3.3V.
So it's recommended to use a debugger...
Hi
I am attempting to add nrf_crypto functionality to the example uart ble peripheral project via SEGGER Embedded Studio on MacOS.
I have opened the project options and...
I have two devices, one is a beacon (DEVICE #1) and the other (DEVICE #2) collects information from the beacon. I'm advertising with a transmit power of 4dBm. I want to reduce...
I have previously had success with programming the nRF51 Series using the nRF51 DK and want to use the nRF52840 DK to program a nRF52840 that will be run in High Voltage Mode...
From the cmakelists of bootloader in Meshv320src, I found the code "create_hex" but this code cannot found in CMake's document. How can it work to generate the hex file?
I am using SDK 15.3 and wanted to ask that if there is a while loop where I can check flags and increment tickers. The program at the moment gets stuck inside
Suggestions...
hello, I have two questions for SAADC of nrf52832 when we use nrf52832 SAADC for voltage measurement.
The AIN0 is connected to the pin to be measured(the voltage is about...
Hello, I encountered the following error when compiling the SDK16.0.0 with keil5.26, how to solve it?
compiling system_nrf52840.c... RTE\Device\nRF52840_xxAA\system_nrf52840...
Hi,
I am using nrf52832 with softdevice s132. The peripheral device is nrf52832 and central device is a mobile app. I want to disable BLE in nrf52832 and I am using this...
Hello,
I have tested the example code of the nRF-IEEE-802.15.4-radio-driver and now I'd like to modify it.
How I can disable the ack? (I tryed this function: nrf_802154_auto_ack_set...
Hello
SDK 15.3.0
4 year old post describing flash storage libraries:
https://devzone.nordicsemi.com/f/nordic-q-a/13821/difference-between-persistent-storage-libraries...
Hello
I try to use this bootloader https://github.com/williamhuang03/STM32F4-Custom-Bootloader on STM32F4 which works well through cable but as suddenly I use Nfr51 as transmitter...
Hello All,
I want to perform an Rx blocking test for my nRF52840 BLE chip which is installed on my custom board. I wan to transfer the packets from device to other, and...
I take the external PWM signal, I directly used the method of controlling the GPIOTE register to be successful.
But I can't achieve the same effect using the program in...
Hello,
I'm using nRF52840( PCA10056 ) of SDK 15.2 to debug long range mode. And I have already followed the steps in thread: https://devzone.nordicsemi.com/f/nordic-q-a...
