Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
Or is there any LCD you could suggest that doesn't need that much code? Simple numeric 2rows would be enough. Want to use it with the nRF51-DK to display some measured valued...
Scenario: I want to use an Arduino shield with the nRF51 DK. When attached to an Arduino, the Arduino's barrel jack is plugged into a 12V power supply. The shield takes advantage...
I am working on a ble project using the nRF51422 and IAR. I can load the code onto the board from IAR and it works as expected, but I run into errors when I run the code with...
Hello there,
I use the MasterEmulator.dll with LabView and the nRF51 Dongle and everything works fine in the past.
Now I had to change something in my LabView software...
Hi all,
recently I tried sd8.0 and i used the example "ble_app_hrs".
the strange thing is in my phone i can see device advertising but cannot connect to it successfully...
I tried to use this example with a nRF51422 and the board of N5 Starter Kit of Dynastream. I adjust all to make it works fine: custom_board and so on.. And I used the Soft...
From SDK 7.2, we have the following definitions:
components\drivers_nrf\pstorage\config\pstorage_platform.h
typedef uint16_t pstorage_size_t; /** Size of length and...
There was something in the webcast yesterday about a Nordic nRF52 roadshow/tech tour/worldwide series of events.
I hunted around the nordicsemi site but didn't find anything...
hi,
i am working on ble project where i am trying to develop a project with master(mobile phone)-bridge(acting as master and slave,nrf board)-slave(nrf board) .i use the...
Hi,
I would like to save the most energy when going to sleep mode. In particular, I want to turn off all modules except the RTC timer.
So, after shutting down the radio...
Hi,
How could i implement Just work pairing method in my "ble central and peripheral" example. I modified project to suit my need, and everything works fine, untill i try...
I am working on a ble project ,'ble_central_and_peripheral",s130.In this project the device acts as master and slave. It connects to the slave only if the address is predefined...
I may be missing something. I am trying to generate a square wave from a GPIO pin in a BLE application (SoftDevice 8.0). I tried libraries (nrf_pwm.c and nrf_pwm.h) in this...
