Hello community,
I recently was trying to evaluate the GC9A01 display from waveshare, I used the github source code as the base code to test this. Attached the link below...
I'm currently developing a USB dongle using the nRF52840 , and I'm facing an issue with inconsistent data reception intervals. I’d appreciate your insights on this problem...
I'm using a nRF52840 configured as Central and Peripheral, with nRF5_SDK 17.1.0 (I'm Not using Zephyr) for reading the Device Name from the Generic Service of a beacon. I...
On future revisions of the nRF52840 Dongle, and on future development hardware of a similar form factor, I'd recommend putting a debug connector that's compatible with the...
Hello,
I am trying to measure nRF9151 current using Power Profiler Kit II, running Cellular UDP project on EVK and following the steps in:
https://docs.nordicsemi.com...
Hello,
We are working on an NRF5340/NRF7002 based project with NCS 2.7.0 SDK. We have been able to get Amazon Root CA 1 and 3 working with the following .conf:
Now...
Hello,
I am working with the nRF7002 DK board and attempting to use the "Light Bulb Matter" example from Zephyr. I am encountering issues when trying to connect the board...
Hello!
I am using a keyboard (4x3) and the rows are configured as input PD and columns as output set, after a successful interrupt , the columns and the rows shift settings...
I am using nRF8001 bluetooth ble for my project. I would like to get the RSSI value as a reference value in my firmware. Is there any way that I can get the RSSI value from...
Hello,
I'm using the following (nRF51822-Beacon): www.nordicsemi.com/.../nRF51822-Bluetooth-Smart-Beacon-Kit
I would like to use the beacon for beacon-to-becaon and...
I am calling the spi_master_send_recv in a ISR from a GPIO using app_gpiote.c It causes a hardfault on APP_ERROR_CHECK(sd_nvic_DisableIRQ(p_spi_instance->irq_type)); Otherswise...
Hi,
The nRF Toolbox app on iOS crashes when opening user added files in the DFU. These files are added to the app via iTunes. The version of the nRF Toolbox is 1.7 which...
Hi,
We're producing a custom board based on the nrf51822 and would like to add a USB Serial chip.
The current contenders are:
a) FTDI 232R
b) ATmega8U2 ( www.arduino...
As the picture shows, I saw this softdevice_hex option available.
The error says, "require nRF_SoftDevice S310_Hex".
But where to this missing component.
My development...
Im sending an 8 bit int using my AVR controller as follows:
static uint8_t* dummy_heart_rate = 6;
aci_loop();
if (lib_aci_is_pipe_available(&aci_state, PIPE_UART_OVER_BTLE_UART_TX_TX...
Are there any pins that I can NOT use for SPI on the nRF51822? I'm not seeing any notes in the latest documentation but would like to make extra sure before I spin a board...
Hi there,
Using mbed i have currently programmed an nRF51 DK to transmit data through a custom service with 6 read only characteristics. Is there a simple way i can alter...
Hello.
I cannot get my head around app_timers. After reading the docs, examples and answers on the devzone I'm still unable to get it running. The timeout callback isn...
I am trying to add SPI to the ble_uart_example on my nRF51-DK but when I try to debug my code debugging just stops (All "step one line" etc. buttons grayed out) at this line...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hi,
I'm using nRF51 Development Kit to program the beacons. I've connected the beacon just like it's described in the last update of this thread using the 10-pin adapter...
Hi,
I just noticed that the nrf51822 doesn't have an eeprom and I already had the pcbs done. Can I use the NVMC to write USER data on the CODE (is it flash memory are?...
