Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
Hello Everyone ,
I want to use pstorage for my project.i get the example code from here
devzone.nordicsemi.com/.../
and its working properly(i.e read and write operation...
I am using nrf51822, after establishing connection between master and slave, circuit needs only tx antenna, is there any way to put rx in sleep mode for ble application? During...
I have some nRF51822 MBED kits and I want to use them for BLE for both peripheral and central roles. I understand that this is possible with the S130 SD and the Nordic SDK...
Hi, this question could be ridiculous question due to my lack of data structure knowledge.
As you see in the HID keyboard example (SDK 7.2), there are several buffers....
I am trying to debug my code today and am finding that Eclipse is constantly breaking execution at the INLINE function app_timer_evt_get(). I do not have any break point set...
It took a bit to learn these offsets and configure the keil project for them. Do these need to change now that I want to begin using the OTA bootloader? I'm imagining that...
It's probably a rare bug, but it is still worth noting. I have been debugging this issue for a day.
I am using SDK 6.1 at the moment.
The problem was that Device manager...
Hello everyone, right now i make my own nrf51822 kit. it works good for all sample example when i use minimum current consumption example it shows 4.5uA current, then i erase...
I would like to create a sensor network consisting of up to 17 nodes, I've been collecting a lot of information about means of communication between them and a computer and...
Hi All,
From the data sheet nrf51822 have a aes hw modules which is used bt softdevice s110.
If i disable the pairing key .
Can I use the inbuilt aes module from...
I am using DEVICEID as an identifier (I know it's not necessarily unique) but when I break the two 32-bit numbers out into bytes, I am finding that the three most-significant...
Hi Nordic, I'm following a guide on this link hrm . I was testing the application with Master Control Panel 3.7.1 with my nRF Development Kit PCA10028. I looked up some of...
We all know we can send acknowledged data in Ant channel.
But based on my test. the acknowledgement message coming back to the originating device is just a dumb packet...
Hi,
I'm new to coding on this platform and i'm having issues. I have an ADXL335 acc sensor connected to P0.04, P0.05 and P0.06 of my NRF51822 (on a custom board). Please...
I cannot get uVision to recognize the J-Link OB device on my nRF51 Eval board. uVision DOES work with a different J-Link OB eval board targeting the same device, the Rigado...
