Is there a way to recieve more than one write callback for a given characteristic, per radio session? It seems like I can rx 1 time per attribute per radio session and tx...
If it can work with iOS blue setting will be better
I need some reference to dev hid device in IOS
but I can just find my device ,connect ok but not work.
I need to create timeout below 1ms. I would pretty much like to use timer for that because I do not want to hold the cpu inside cycle. For me it is not important the exactness...
Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
It's not really a question but a request to Nordic.
Could you change the #ifdef lines in gcc_startup_nrf51.s to .ifdef. So:
.ifdef __STACK_SIZE
.else
.endif
and...
Hi,
How do I determine the application address? The one that is to be programmed to UICR.CLENR0.
I have SD S110 V7.1.0 but I didn't find this information in the release...
Hello,
I receive NRF_ERROR_INVALID_STATE error quite a few times because my own state handling is still a little buggy. I want to find all these errors. What would be the...
Hi all,
Please I want to make sure of something. In the s120 specification, it's written " Bluetooth low energy combined Central and Peripheral SoftDevice", and even in...
Hello,
I need to read the UID and later on also the RSSI value of devices (Handys) in range.
It should be reading the values automatically without the need of manual connecting...
The datasheets for the nRF24LU1P ansd nRF24LO1P have near identical example antenna driver designs which vary in the values for the inductors, etc
The LU1P datasheet is...
Hi,
I've combined twi_sw_master and DFU in my project based on nRF51822 Beacon v1.1.0. Now I can't connect to the beacon. The same project only with DFU or only with twi_sw_master...
Error is shown in the following figure.
I use nrf51822-DK(256k)
The exception of BLE_S110 works well.
Memory Is not enough when you add a BLE_S110
Is there any...
I am using S120 v2 with SDK 6.
Initialization of the softdevice and device manager return no errors.
However when I want to start a scan for devices, the function checks...
I am using PCA10031 dongle with SDK 7.2. I tried the blinky example in peripheral directory. Unfortunately it didn't work for me.
When I use the makefile from blank/armgcc...
Hi,
I am using Timer0..2 interrupts along with radio TX/RX. When the Timer2 interrupt coincides with RX/TX the Timer2 is halted for approx. 450 µs during TX. Is there a conflict...
hi...
i am working on nordic nrf51822 evaluation board.i coudn't get pin 31 interrupt.but in all other pin i can get interrupt. maximum of 3 gpiote pin events is using...
I'm following the example here for the PCA10028, only the example I copied from the Pack Installer is called ble_app_hrs_s110_dfu_experimental_pca10028 (nRF51 PCA10028) instead...
