But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
I have an iOS App which is just designed for updating our device firmware OTA. It uses the Nordic DFU library, updated to the latest cocoapod. It connects to our device, and...
Hi,
I use OpenWRT and nRF52832 to develop a BLE gateway, the nRF52832 connected to OenWRT through UART. Now,we need the uart serial DFU of nRF52832, and I found that nrfutil...
I am looking for some advice before diving in to what could be a big waste of time. In my existing Thread implementation, I use nRF52840's in two different configurations...
Hi all!
I am using mesh sdk v4.10 and sdk 16.0 with an nrf52840 custom hardware. I have a question regarding the mesh event handler. I am seeing something weird which I...
I am trying to run DHT sensor on the nrf9160 using the sample provided by zephyr (can be found under zephyr>samples>sensor>dht). The code was meant to run on nrf52. Is there...
hello everyone,
I'm using SDK15.2 in nrf52832. I need to update my sensors value(Temperature, Humidity and accelerometer) data to advertising non connectable beacon. How...
Hi,
I'm using nRF52832 board and I'm modifying the Eddystone BLE Application in ble_peripheral example in SDK 16.0.0. I'm trying to get the characteristic value of ADV Advertising...
Hello, we are creating a nordic peripheral using an nrf52832 and SoftdDevice S112 and SDK 16.0. We need to store quite a bit of data non-volatilely, at a fairly fast rate...
hi
im use nrf52840 as a gazell device which run the demo \nRF5_SDK_16.0.0_98a08e2\examples\proprietary_rf\gzll\gzp_desktop_emulator\pca10056 ,and use nrf24lu1p
(\nrfready_desktop_2_v3...
I am porting a peripheral project from nRF51822 on SDK 11 to nRF52832 on SDK 15. Currently I'm using15.0, with S132 6.0.0. I used the template project for an initial pattern...
Haii i'm using Nordic nrf52840 with SDK 15.0.0 and soft device of s140
now my issues is i want to connect a four device to the central and there should be Bidirectional...
To establish a connection to a nRF51 Dongle I have recently following problem:
A J-Link Window “J-Link Window_Device Selection.png” appears and in the following Window ...
Hello everyone,
I'm developing a custom software with SDK 15.3, SD 132 6.1.1 following the ble_app_hrs example for supporting Peer_Manager and Encrypted Link.
This is...
Hello!
I am trying to get the old window application for the Power Profiler Kit v1.1 at https://www.nordicsemi.com/Products/Power-Profiler-Kit but the page is not available...
