Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hello:
I'm testing nrf9160's A-GPS function, and I find that an error of SUPL will be reported at runtime:
I use master branch of the nrf repository(nrf/samples/nrf9160...
I have a Windows 10 laptop (Acer Swift SF 514-52T) where I have installed the setup for nRF9160 from "nRF Connect for Desktop".
All steps followed.
I got some issues...
I've got my application wrapped in mcuboot for HTTP-based firmware updates which is working fine. In the past couple days I've enabled CONFIG_NVS using the code in zephyr...
Hello all, This is my first post on your DevZone. Setup details: nRF9160 DK Board: 0.8.3 nRF Connect SDK tag: 1.2.0 OS: Windows 10 Pro LTE Network: NB-IoT on B3 and B20, Operator...
Hello, I'm using nRF52811 and It works with 1.8 voltage on it's VCCs. Is it possible to use a micro SD? Should I use a voltage level translator (for example TXB0108)? I know...
Hello all,
I try to import Keil project into Eclipse with Makefile. I managed put all my source file to be compiled, and my include paths etc.. in my Makefile
In Keil...
Hi,
I am working on one application in which I want to sample ECG at 1000 samples per second continuously and battery value at 15 seconds interval. I am configuring two...
Hi,
I'm trying to connect my phone ober BLE with the nrf52840. The first x attemps always work (connect, disconnect, connect, disconnect, ...) but after some time no further...
Hello guys,
I`m pretty new in socket programing, I have a question , is there any way to trigger an event for a file descriptor that is used in poll() function ?
For example...
Hello DevZone,
Recently I've been testing connecting multiple servers to one client and fiddling around with some settings regarding timing and packet size.
In the following...
Hi everyone,
Recently, I have bought two nRf52 DK, and I want to test the latency between central and peripheral in 2Mbps.
Can someone give me some suggestions about where...
I develop BLE Beacon device using nRF52832. I want to set the device name by combining "XXXX" and the lower 3byte of MAC Address. "XXXX" is used to recognize it as a company...
Hi,
I have a modified template of the ble_app_template example from sdk 15 NRF58240-dk pca 10056 s140.
I have written a custom function as per this tutorial : https:/...
Hi,
I followed the "Getting Started Assistant" to setup SEGGER Embedded Studio, but after opening the GPS example for nRF9160 i end up with Import Errors. 1> main.c:8:10...
My production app(sill in development technically but pre-production stable) is having issues with our SDK14.2 BLE UART application. When the generic version from examples...
