Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
Hi,
I'm using nRF51822 Beacon v1.1.0. Is it possible to detect that the beacon is being scanned? Is there any event generated during this process that I can catch?
I have been studying the ble_app_hrs example, but it has unnecessary functionalities, and it is hard to understand.
Do you have a simple application for transferring data...
I would like to use that chip with appropriate codec as wireles Tx/Rx set. I need of uncompressed audio signal and my sours will be analogue amplifier and the Rx module has...
Hello there,
I am using multilink_central example on nrf51822 Soc, and I charged S120 in the memory. I am trying to get the RSSI and the MAC address without getting connected...
I am trying to get the sniffer to run and having problems. Tried both 0.9.7 and 1.0.1 same results on both. OS is W7-32 home. Hardware, have tried several PCA10000 and a PCA10001...
Hello community, I have the uVision 4 installed, I tried to open the project to compile ble_app_hrs_dfu but get the following error.
I find this file in C:\Keil\C51...
The reference designs and sample layout use 0402 sized components in the RF section. Are 0402 sized components required or can 0603 sized components be used? I'm trying to...
how i can send and receive data by multiple nrf24l01
for example :
If I have 10 packets for send .In Deviec 1 I want send 5 packets by one nrf24l01 and send 5 packeets...
Hi there,
I am struggling for 4-5 days but could find a solution yet.
Can nRF8002 be used as a beacon? I read nrf8002 datasheet and also google it alot but could not see...
If the softdevice is not used, As follows:
static void gpio_init(void)
{
nrf_gpio_cfg_input(Record, NRF_GPIO_PIN_PULLUP);
nrf_gpio_cfg_input(Play, NRF_GPIO_PIN_PULLUP...
There is an input clock signal with frequency of 3MHz-5MHz, but the exact frequency is unknown. I want to use nRF51822 to detect the clock signal's frequency, the accuracy...
Hi, I was using LG's HBS750 (Bluetooth Headset).
This device , after it is connected to an iOS device, shows the headset's battery level.
(Device Spec : Bluetooth 3...
Hi,
When running the multi-role-conn-observer-advertiser example on nrf51822 Soc with S110v7, I never be able to get the MAC address, and even the RSSI is always 0x1.I...
Hi all,
I am trying to implement a scanner (for reading RSSI and MAC address of the advertisor) , and I am based on S120\multilink_central example.
I understood from here...
