I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I have a test set up using the ble_app_hrs example where I increment a dummy uint16_t periodically and then send that value up to the nRF Toolbox iOS app to plot. I want to...
Hi all,
I would like to use the strcmp - string compare function, however don't know how to create a string from character array. Standard way would be something like this...
I can transmit data from my device (the server/peripheral) with the ble_app_hrs , but want to modify the peripheral behavior with some basic commands sent from the mobile...
I'm migrating from S310 v1.0 + SDK 5.2.0 to the latest S310 v2.0 + SDK 7.1.0 (to be able to update also BL and SD).
I have used OTA DFU based on example included in SDK...
Does the sdk7.1 + softdevice support flash_page_erase function?
Also, for the spi_master api, is the spi_master_event_handler required or optional?
currently, the...
Hi,
How to separate flash memory area that will not be overwritten when you upload new application code (e.g. a few bytes of static data). I'm using Keil.
Hi, I just flashed the BLE_proximity example in the ...\nrf51_sdk_v6_1_0_b2ec2e6\nrf51822\Board\nrf6310\s110\ble_app_proximity in the nRF51822 Development Kit, and the nFR...
I am working on a custom BLE service on the PCA10001. I can successfully detect and communicate with the PCA10001 using windows x64 MCP. I can also detect and communicate...
Dear Sirs
I am new with Nordic BLE Modules.
After successuful pairing with Windows 8.1 in a Tablet I need to get an active Service. For example I would like to obtain Battery...
We have an NRF51822 running S120 at 32MHz.
Our system has two removable batteries. If a battery is removed we need to switch to the other battery as fast as possible. We...
For TWI, SPI and UART is there a significant power savings from powering down the unit when not in use vs just disabling it?
Disabling the unit seems reasonable, but powering...
Hi!
I was trying to use nRFLoader to update firmware using example DFU Bootloader but app hangs on "Discovering" (after selecting device to update). What can be the reason...
Currently I can upload new application firmware smoothly (I use the dual bank setup). However, I have to use packets of size 20, so this takes a long time.
Is there actually...
hai ,
i am using the NRF51822 development kit. The NRF51 dongle i have used as a sniffer and a master control panel. Is it possible to load and run a s130 softdevice and...
Hi, I'm trying to estimate the nRF51422 current when running ANT. Does the softdevice use the RTC (LF oscillator) when in wait mode to save energy? Thanks
