Hey folks, we are planning to implement BLE Audio based on one of the Nordic ships and unfortunately nrf54H is not really available now and nrf54l does not support LC3 audio...
I'm trying to flash the hardware even with Programmer v4.6.0 but i get the following issue
18:59:55.179 Initialising the bundled nrfutil device 18:59:55.561 Using the...
Happens consistently and in production.
The stream advertisement is still there but cannot be connected to by any receiver (both 3rd party and our own). 3rd party says connected...
Dir Sir
I have bought thingy 91 X for evaluation purposes
After activation of the Sim and, I have a constant green Led on
The device does not connect to the web application...
I just want to double check something before I optimise an implementation.
If burst is enabled on multiple channels, let's say x256 for two channels, internally is the process...
Hi there,
In our device we are using nRF52832 with SoftDevice S112, SDK 17.0.1 and embOS Safe. Up until now we were working with the “Just Works” setting of BLE connection...
Hi
I have two DKs, previously they work well, however, after I add the nRF21540 FEM on each DK, I always receive this in my central device:
Whether the amplifier cause...
I've been seeing occasional failures of my application which I now believe are due to a bug / design flaw in the app_timer library module.
The problem is due to a race...
Hi :
I have problems ,for gpiote interrupt hanlder can be hanged up by softdevice. In normal use ,I should pull up sck pin of my private ADC chip for less than 10us and then...
Hi,
I'm using the SDK 12.2 with the sd 132 3.1.0, and actually I'm trying to send two separate advertisements wich I'm swapping every "radio notification event", but I...
I am working on modifying the ant+ sdm example to hack my treadmill. Got the example running and talking to my Garmin watch and the display simulator. All of that seems straight...
This problem didn't appear every time when I upgrade firmware. If I restart my app again, sometime the SDK can works well.
Anyone can help? I'm use SDK in Android, Legacy...
Hi,
I am using nRF51-DK and nRF5_SDK_12.2.0_f012efa. I have programmed Proximity example from the SDK to the Development Kit and was able to successfully program the DK...
I have a function with a return value in the time slot, after the function is done inside the time slot signal callback function, I want to use the event callback function...
Hi
We'd like to set the pairing timeout when using the function sd_ble_gap_authenticate(conn_handle, p_sec_params) . The reason for this is that we are setting the connection...
(/attachment/182b723590b3c447267d5aed62b5405f)hi, i want to work on PWM to controll the vibration coin frequency for certain time period and also to change RGB values of LEDs...
Hi!
I'm reading the PS for nRF52832 and I can't find a clear answer on the following question.
If I set up a GPIO channel with pull-up/pull-down in the PIN_CNF[n] register...
Hi, I'm learning to use the nrf52832 (PCA10040).
I'm on SDK12.2.0 S132.
I've done those basic tutorials while merging codes from the examples.
My code can currently read...
Hi, i am working on TWI sensor example in SDK11 i have connected MMa7660 to PCA10040 board as per the GIPIOs. and am integrated BLE app uart to the same TWI sensor example...
Hi,
I am using a custom board with a nrf51422, SDK11, S130 v2.0.1 with central role.
I have made changes on the code to change from MID bandwidth to High. I added the...
Hello,
I'm using the Nordic BLE-UART service found in the SDK. This is the "ble_app_uart" file in the SDK examples for the Nordic nRF51822. I'm basically sending JSON back...
Hi. I'm using nRF51822AC, SDK12.2.0, S130 v2.0.1 as central.
I want to make only app image for DFU.
I made a command as below refering to github.com/.../pc-nrfutil.
...
