I will be deploying my nRF51822-powered devices into the field and the end user will not be able to have any physical access to, for example, power cycle the board. I need...
Hi,
We are using the ble_app_uart example in evaluation board to read data from some sensors and send it to the nRF UART V2.0 in Android 4.4. Every 20 ms I am trying to...
I am try this at nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
Firt I connect to Android device and keep one whitelist.pp_addrs and one whitelist...
Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hi, I wanted to ask a question regarding sending data.
I currently have external memory that will send out serial data (SPI) to the nordic microcontroller. I have saved...
I want to make a frequency of 750khz, 50:50 duty ratio.
How do I use pwm?
I use it. nRF52832 PCA10040
I used the PWM library example but it failed.
The frequency...
I'm using nRF5SDK V.12.2.0.
In the app_ble_uart example, trying to change MTU size as below.
#define NRF_BLE_MAX_MTU_SIZE 103
...
#if (NRF_SD_BLE_API_VERSION == 3)
...
I am using SAADC with TIMER3 and PPI, sampling 12bits at 250Hz.
When I use 10uS acquisition time, the average current consumption is 300uA lower than when using 3uS or 5uS...
With nrf Toolbox 2.2.1 on android 6.0.1 (Google Nexus 7 or OnePlus 3T), I try to transfer an application firmware in a zip file UiBoardV0.4.1.zip , generated with "nrfutil...
Hi,
In am using a nrf52832 in a serializated configuration, with the softdevice S132 on the connectivity board.
Is there a way to configure GPIO on the connectivity...
hello,
i have one nrf51 dk and it has some advertisement packet, i have another nrf51, i want this another nrf51 to copy first nrf51's data. can you tell me how to copy...
I stumbeled across a problem with my application, which runs on s120. My case is: I have a S120, configured as a peripheral and I have an Android 5.0 Motorola smartphone....
Hi, I'm trying to install the BLE buttonless DFU template onto a nRF52 (PCA10040) eval board using the secure bootloader example (with s132, version 12.2 of the SDK) via nRF...
We have a new project it is as preipheral. It will support dual bank OTA. We want to use the IC of nRF52832 and use SDK12.2. I want to know which softdevice and bootloader...
I bought new nRF52-DK. I am am trying to connect it to windows 10 system over usb 2.0 mini port. I have installed nRFgo studio and JLink drivers. The problem is nRF52-DK is...
Hi, Nordic
I have one nRF24LU1P, I program app to made it as USB Dongle.
Now I need to disable usb suspend or once USB suspend, app resume usb immeiately.
Could you...
I'm using the SPI Master driver code on the nrf52 using EasyDMA to talk to a SPI slave (Adesto Flash chip)
I can successfully initialize, read, write and read-back from...
I'm designing a BLE peripheral with a custom profile composed by Hearbeat, Device Information and Battery service plus a custom service for device operation parameters configuration...
Hi,
we are trying to develop a BLE keyboard that work with android and ios. We made custom board using nRF51822 and keyboard driver IC with a qwerty keyboard layout. We...
Hi,
In SDK nRf51-SDK_9.0.0.2e23562, I call sd_ble_gatts_characteristic_add().
I set the p_cccd_md read_perm as BLE_SEC_MODE1LV2 or BLE_SEC_MODE1LV3, and set write_perm...
