after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
Hello,
I am migrating a BLE project from SDK 13.1 to SDK 15, and am running into an issue with SPI functionality. I have followed the migration guide for 14.2 to 15, changed...
Part 1: A device that is exposing Mesh Provisioning Service[as a unprovisioned device] or the Mesh Proxy Service [as a provisioned device] could under-utilize the negotiated...
I am using nrf52832 and i want time.
I am using nrf_calendar_example https://github.com/NordicPlayground/nrf5-calendar-example .
My problem is it gives only resolution...
Hello all,
I have noticed that a delay appear periodically when writing SD card for example, I have something that the following code
Unfortunately, I have a jump...
Hello Nordic Team
I am working on nRF52832 MCU, SDK-11. I want to calculate available space so that I can save custom sensors data in chip.
According to datasheet we have...
I am working with nRFx modules and have a few questions about updating parameters. I started my project with an example and modified what I needed. However, I am not sure...
Hello Nordic experts,
I am trying to add an output endpoint to the usbd_hid_generic example in nRF5_SDK_15.0.0_a53641a. I exactly followed the suggestions in
https://devzone...
Hi,
I am using nrf52840 preview DK as a transmitter and try to get rssi by a linux lib. and it works well. and now I want to find advertisement channel number, because the...
I try to integrate Mult-touch(touch screen) and Keyboard feature in a single program, when I run this program, the phone side(Android8.0 based) can only receive Mult-touch...
When using nRF connect for desktop on ubuntu I can't go through the "Select serial port" step because I got the following error message:
"Could not open the port. Please...
With the release of SDK 15 has come the new nrfx module API's which seem to be easy to port to. One thing I have seen in the nrfx templates is the use of the nrfx_config.h...
Hi,
We are using nrf52832 micro controller and our device is consuming about 14mA current right now.so i have 2 querries that
1. How can we put our nrf into low power...
Hello,
I encountered an interesting issue with SPI0 on the nrf52840 that I cannot explain. In short, my SPI bus would stop working shortly after communicating with my slave...
