Hi,
I just started to interface the lcd display with nrf51822 evaluation board. The display i'm using is, spi compatible, 18" tft (160x130) from tiny lcd. I took spi master...
Hi,
We are using the nRF905 device in an application where it needs to switch between auto-retransmitting and sending single packets, due to it communicating with several...
This is not a real question for support. It's more a success story i'd like to share with you!
Our company develops firmware for various customers on a lot of different...
Hi all,
What is the maximum data rate for the nRF24AP2 when using the Synchronous serial interface?
I cann't see it in the datasheet.
Is there anyone can answer me...
Hi,
In my design, there is a tag used by 24l01,It can transmit the temperature value.In the tag, the parameters are like this:
addrofch[0] = 0xe7;
addrofch[1] =...
We've been working on a product that utilizes a NRF51822 chip as well as WS2812B NeoPixels. Since there have been numerous posts about it here we've decided to release our...
Due to limited resources we are looking for someone who can help us with making a custom profile.
You are preferably in the Stockholm area and have done this before.
The...
Hi,
I used SDK_15.1.0, secure_bootloader/pca10040e_uart.
Through PC uart,it update successfully .But boot through android(linux) uart,it returned 'invalid crc'.Can anybody...
Hello,
I am working on BLE Peripheral and Central part on SDK11 for a long while. Now i want to start with NFC.
I tried to go through nfc section in SDK14 but could not...
I am observing a surge startup current of 0.1 to 0.2 mA when I am powering the nRF24LE1 module. Is it possible that the device can startup in power saving mode? Is there a...
Hi
I had used one nRF52 Kit(nRF52832+nRF5_SDK_14.2.0) to connect a BLE 6LoWPAN Border Router(Raspberry Pi 3B+Raspbian)
according to the IoT User Guide.
But in IoT applications...
i am using ubuntu 16.04
using eclipse photon IDE
nrf52_14.1.0 i am unable to run to run more than two threads can u please help me out in this
i am trying "nRF5_SDK_14...
Hi,
I am working with bonding process on Android App.
My problem is:
When I create bond to nrf51822, the process complete successfully. Then after a few seconds (3-5...
Dear Nordic Team,
Thanks for supporting .
I have a custom hardware for nRF52832 its working for nrf_beacon example but its not work with eddystone beacon example.
please...
We’re working with the NRF52, SDK 14.2 and SES.
Somehow we have managed to have our boot loader extend into our MBR params page. We extended the stock SDK 14.2 boot loader...
So using the above code I am trying to set the threshold of 2.3 volts on the power comparator. I am using sdk12.1 with Soft device 3.0.0 on an nrf52832
I keep getting NRF_ERROR_SOC_POWER_POF_THRESHOLD_UNKNOWN...
board nrf52840
sdk 15.2
hi i have one problem in connection, once i connected the device and disconnect means ,the device stops advertising..if i reset means it will show...
Hi, I have a problem when write data to flash on nRF52832. my code is like below:
err_code = nrf_drv_clock_init(); APP_ERROR_CHECK(err_code); // Activate deep sleep mode...
Hi Nordic:
I migrate my application from mesh-2.1.1+sdk15.0.0 to mesh2.2.0+ sdk15.0.0, but there is an issue when calling mesh_stack_config_clear()
Following are my steps...
Hi,
I'm using nRF51 (softdevice S130) in my project as BLE peripheral to send data to my smartphone. The current data flow has become insufficient because the maximum MTU...