I have a working project where pin 16 is configured as a low-level interrupt source.
it is working well with SDK 15.3
after porting to SDK 17.0.2, it is not triggering...
Hello Nordic Support Engineers and fellow developers ...
Just a note to thank everyone for help via this forum. I started very inexperienced with Nordic SDK a year ago and...
Hi,
I recently purchased a thingy91 for a project. I'm trying to follow instructions from a Nordic youtube video ( https://www.youtube.com/watch?reload=9&v=xQ7hDzRULJQ ...
I have a nRF5340PDK, Now I want to know the lowest power consumption of this chip in different condition, such as adv, connect, sleep. But I am not sure how to config the...
Hi, i am using:
-nRF 52 DK
-nRF 52832
-Sensor of Maxim Integrated
-SDK 17.0.2
I have some problems in handling the I2C through the nrfx module.
This is my ReadByte...
Hi, I have a set up consing of an nrf52840, a Raspberry pi and a Linux workstation, which communicate over IPSP following the IPSP sample from Zephyr OS. The nrf52840 is a...
Hello,
I have the proximity example updating the battery service value fine using the provided nrf_drv_saadc.h driver. When converting the saadc driver to NRFX (nrfx_saadc...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi,
It seems to me that unused GPIO pins can stay float. However, earlier questions made me less confident.
Is firmware setting is enough?
Thanks,
Daniel
1. Is it reasonable easy to get a stable throughput over 1Mbps at a 3 meters range? 2. How much CPU resource is available at above situation? Or how many DMIPS is left at...
Hi
I am working with S130, sdk12.3 NRF51422_xxac
I have been successfully testing bootloader DFU example (secure_dfu_secure_dfu_ble_s130_pca10028) on the NRF51 dongle...
Hi,
I had tried the Thread Topology Monitor using nRF52840 PDK which was connected with PC via USB cable, and flashed it with Thread CLI example. But there was no serial...
Hi, I am having a problem related to BLE security.
My application model is a nearby network with no connection using BLE. My plan is using advertisement channels to broadcast...
Hello all,
I'm working on updating bluetooth communication. Currently using a module that receives AT style commands.
The first step will be replacing with nordic device...
Hi,
I need to use the SAADC to check battery status (infrequently).
I would like to do this in blocking mode without accidently leaving the easyDMA powered-on unnecessarily...
Hi,
We use the flash manager to store our custom data structure in flash.
Since it growed and eceeded FLASH_MANAGER_ENTRY_MAX_SIZE we get an assert in flash_manager_entry_alloc...
Hi,
i was interfacing oled with nrf52 board. I got some example and modified bit to use it with GCC.
But it is now working. Oled not at all starting.
oled is 0.96 inch...
I'm using the Custom service example as by base. Now this was really itching me to not know the reason which causes it. I'm giving an "if-else" condition inside a "switch...
Hello,
I'm working with :
- nRF mesh SDK 2.1.1
- light_switch_proxy_server
- I implemented the generic model on / off
I work with a module (server) that has two...
i got this error when i am porting the code for nrf52810.i am working on the spi protocol i am porting code from nrf52832 to nrf5810. I am done the as per instuction given...
