Hi,
I am getting randomly incorrect SOC reported by pmic npm1300. For most days, it reports correct SOC but then all of a sudden it starts to report incorrect SOC even though...
Hi,
I recently found out about the Periodic interval feature on GRTC CC[0] and it seems like it would be quite useful for my application. Most of my code so far uses the...
Hi,
I have integrated Neuton’s “Transport Type Detection” pre-trained model into my firmware, running on a nRF52840dk. For collecting 9-axis IMU data, I’m using the ST X...
I'm trying to implement a fall detection feature on the headset side using the LSM6DSOX IMU sensor. The IMU is configured successfully, but the board halts after the INT1...
I have a ready hogp struct and I'm trying to subscribe to an input notification (I'm connecting to a bluetooth keyboard) and I'm getting error -22. Here's the callback in...
Hello,
I am trying to count pulses on nRF52840 DK's pin for measuring water flow with hall effect sensor. I tried to implement PPI + GPIOTE + TIMER in counter mode, but...
Hi, I am using nrf52840-based custom hardware and have an external flash connected on SPIM3. Till now I was working with my other peripheral connected on different buses and...
Hello, if I disable interrupt on nrf51xxx device, function sd_ble_tx_buffer_count_get will simply run right into hard fault handler, without returning anything.
I do not...
Hi,
on NRF51 BLE peripheral I want to implement authentication, so only selected BLE masters have access to my BLE peripheral.
There is a password known to BLE peripheral...
Regarding the RTC prescaler of nRF51822,
I found out that it is the following.
Timer and RTC prescaler behavior by TASKS_CLEAR is different,
When TASKS_CLEAR is executed...
My company is making capacitive touch plates and to make them smart, app is used.We are using NRF24L01+ for rf communication between device and app. Our sockets and hub with...
I did some modification from radio test example.
But I don't know why the function "rand8" never ending.
In the function, rand8,
NRF_RNG->EVENTS_VALRDY = 0;
while (NRF_RNG...
Hi,
I have been trying to get up and running since the first DK was released for nRF52x and I am yet to have installed a working development environment. I have tried to...
I'd like to use a DMA channel on the nRF52 to copy RAM from one block to another. However, there doesn't appear to be any DMA controllers that are not directly associated...
Hello everyone
I'm trying to disable advertising but it doesn't work in some cases, I don't really know why. Here is my pretty simple piece of code:
/* Disconnect and...
www.keil.com/.../uv4_db_dbg_evr.htm
www.keil.com/.../EventRecorder.html
Keil worked in a new EventRecorder feature that uses some SWD buffer memory to push data out...
Hello,
A question to understand please. A lot of issues still unfixed in rev 1, but are known for a long time (see errata docs). Like SPI with RX = 1, DCDC -4dB on RF,...
Hello, I try to run the sdk example for adc, i set an input voltage in varying from 0 to 4.38 V in the pin 4 (AIN2), but the returned value didn't corresponds to the desired...
It there a specification for current draw during POR? (From time Vdd starts rising until cpu starts executing?) For nRF51 and 52.
I found this devzone.nordicsemi.com/....
(Hello! I'm drawing the module circuit base on nrf52832 with rfx2401 power amplifier (PA). As I understand it needs to set pins TXEN, RXEN to high level to activate this PA...
It may sound a bit old and you may have fixed them in latest Soft Device stacks however I wanted to share with you a couple of pairing issues we encountered with Soft Device...
