Hi,
I am using "asset tracker" project in nRF9160 DK.
I want to update asset tracker application through HTTP.
So i migrated changes of "asset tacker" in main function...
I have a simple TCP client application running on the nRF9160. After connection to the server, recv is called and writes the data over Segger RTT channel 1, where on the host...
Hi,
firstly, I have to say, I use MBED OS, if you cannot help me because of this, I understand, but maybe somebody still has some general Ideas.
I am trying to build an...
Hi everyone,
Currently, I am working on my bachelor thesis for creating simple network by using MQTT, BLE-6LoWPAN and nRF52832. I have three nodes of 52832 and one raspberry...
Hello everyone!
I want to form an Openthread network with three Nordic nRF52840 cardboards. I would like to monitor the traffic using a sniffer, but i can't receive any...
We are using the development board PCA10040 for implementing a prototype with several GPIO interruptions.
We are trying to use the NFC pins (pin 9 and 10) as pins of GPIO...
Hello,
i have bought 3 modules from Rigado (BMD-330-A-R) with a nRF52810 SoC, is it possible to flash it with an Raspberry Pi? I read that SWD is possible by its SPI-Interface...
We are in progrees of developing a wearable device using NRF52832 with BLE. The problem is, we have quite a few chips dead after several times of rewriting. The dead chips...
Hi,
I tried adding PWM for turning on/off the LED's on the DK for the Enocean switch example. It worked well.
I tried to perform dimming on the switch example by restricting...
Hello All,
This is a trivial question I guess but I am not able to figure out
Working on : nRF5 SDK for Mesh v2.2.0
SDK version : nRF5_SDK_15.0.0_a53641a
I have...
hello ,
can anyone tell me what shall i change in light_switch_client ( server ) to implement the simple_on_off model instead of generic_onoff_client ( server )
i started...
I am using nRF52840 for bluetooth mesh technology for industrial light control.Can anyone help me for my project, how can it be done,I have the light switch demo file, but...
Does any one use mtm m905 module. i tried this module and its a complete failure. the smt package is not standard and the BGA factory failed many times to solder this Module...
Dear Nordic Support Team,
I'm working on a BT Mesh implementation and came across a problem with the proxy enable / disable feature.
Disabling the proxy function doesn...
Hi all, I'm working on making mesh sdk work with peripheral uart example. I tried to merge peripheral uart example (nRF5_SDK_15.0.0_a53641a) into proxy_server example (Mesh...
Hi,
I was into the working of bluetooth mesh. I was wondering if it is possible to configure a bluetooth mesh network with a smart phone acting as a provisioner and by any...
My aim is to establish communication via nRF52840 dongles. This means if I connect mobile phones to the dongle and the data sent by one mobile phone should be received by...
Hi
Does the nRF52840 and 52832 support automatic gain control (AGC) for for BLE?
See this Ti post which suggests AGC is not used for BLE
http://e2e.ti.com/support...
I have recently migrated from SDK 15.0 to 15.2 and are experiencing problems with my code.
I have a nRF52840DK and have attached two accelerometers to this board. I am able...
Hi,
I'm currently working on achieving BLE NUS + ESB UART concurrent implementation via timeslot API, by referring to the example here . I have ported it to utilize SDK15...
Hello,
I'm using nRF5 SDK with version 15, nRF52832 IC and softdevice s132. I need to save hold the data in the ram even in sleep mode. I'm using the below code. However...
