Hello Team,
We are working on custom board using nrf54l15 platform.
If we flash only application code, it works, LED is blinking & BLE advertises. But after adding DFU...
Hello!
I'm currently working with the nRF7002 Wi-Fi chip on a custom board. The MCU used is STM32H573ZIT6, and the software is Zephyr 4.0, specifically using the Wi-Fi shell...
Hi, when I am trying to set up channel sounding, I am looking for the best parameters for CS configuration. The main problem I have is that even with slow movement (1 km/h...
Dear sir,
I'm using the sample application "channel_sounding_ras_initiator" to performing the evaluation. Here are my test environment: - Developement kit: nRF45L151 - Tool...
Hello,
I previously used DECT NR+ modem firmware mfw-nr+_nrf91x1_1.0.2 on nRF9151 DK Development kit and moved on using the new modem firmware mfw-nr+_nrf91x1_1.1.0.
But...
Hello.
This may be a basic question, but please let me know. I am using nRF54L15-DK and nRF Connect SDK v3.0.2.
Is the 32MHz crystal running when the nRF54L15 program...
hi everybody: This is my first time developing an nRF chip and also my first time using VSCode After installing nRF tools and fast (3.0.0), I found that I did not see the...
Hi,
I want to achieve DFU OTA nRF51 using NRF52832.Is it any example,or data transfer message sequence charts documentation? Could you give me some suggestions?
Thanks...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi,
I hope you are doing well. I am working on nrf51822 project. I want the nrf51822 to advertise for 5 secs and then sleep for say 30 mins or an hour and then wake up...
hello,
Starting nRF 52832 (s 132), leaving idle, after 3 minutes, ble_event_id 0x1b will occur, then BLE communication will be impossible.
When ble_event_id is 0x1b, how...
Hello,
I'm having special SPI protocol which requires SPI Slave to toggle REDAY pin after every byte. I do test using 2 nRF52 boards. One is SPI master, another is slave...
Hello all, first time using a I am using a nordic board im a little overwhelmed by all the options. I have nrf51 development kit and I just used the getting started tutorial...
I'm starting a new design on nRF52 and I need to connect a microphone on it. Reading the datasheets and questions here, I found there's 3 solutions for the type of microphone...
Hi,
I was reading the procedure to prepare the NRF52 DK board for current measuring and some questions came into my mind. I understand we have to open the P22 so we interrupt...
I have set up raspberry pi 3 as a border router and programmed the the nrf51422 using the iot_ipv6_coap_server_pca10028 and could successfully switch on and off led3 and led4...
Hello,
I am using secure_dfu_secure_dfu_ble_s132_pca10040 project. Now I want that the user who has specific key can only access the nrf my device and then can send the zip...
Hello!
Does anyone know what's the maximum frequency for SPI (SCLK) for nRF52832 or SDK 12.1? I see following code in nrf_drv_spi.h:
typedef enum
{
NRF_DRV_SPI_FREQ_125K...
Can someone tell me how the DETECT signal works in the nRF52840?
This version of the nrf52 has 2 GPIO ports.
Does that mean there are 2 DETECT signals? or is there still...
