Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit(nrf52832)
2、what is my purpose?
the quality of thingy52 audio demo is not good(iphone7)...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
hi.
I used mergehex.exe to combine the hex of softdevice, bootloader, and application into one, but the board is in DFU state and the application does not start.
I am...
Hi! I'm developing on nRF51 with SDK 11 and trying to extend our application with buttonless BLE DFU support. Due to limited flash memory, we could only use single bank ble...
The website is broken for me, and I see a sequence of orange pop-up messages saying "An error occurred. Please try again or contact your administrator."
When I use master control panel to scan ibeacn, I find "Complete Local Name" in below picture,
How to set the "Complete local name" ?
I heard someone says set in the...
Hello,
I've now been looking for a while but haven't yet found anything working to programmatically unwind the call stack when working with the nRF51 or nRF52.
Basically...
We are completing the design of a PCB and have a mounting/assembly issue with the NRF52840. We In looking at the mechanical spec on your datasheet w find that A row of 24...
hi
1.does nRF5-SDK-for-Mesh v 2 support friend feature of Bluetooth?
2.phone with ble 4 can current to ble 5 mesh network?
3.is there any example of two above?
thanks...
I have connecting problem.
My setting...
1. OS : win10 x64
emulator : J-link(EDU)
2. installed
1) nRF5x-Command-Line-Tools_9_7_3_Installer.exe
2) nrfgostudio_win...
Hello
The scanner causes the code to freeze when a debugger is not connected.
We are developing a system where one of our units is to run on the nRF52832. During development...
Hi ,
I testing the " nRF5_SDK_15.0.0_a53641a\nRF5_SDK_15.0.0_a53641a\examples\ble_central\ble_app_uart_c " sample code with nRF52832 . Found sometimes get the advertising...
We are using nRF52840 with the nrf5_SDK_for_Mesh_v1.0.0 in combination with s140_5.0.0-3.alpha I'm working with the nRF52840-Preview-DK board. Task: program a bootloader for...
Hi, developers !
We are going to make a USB dongle that configures RF HID using nrf52840.
So when I look at the datasheet for circuit configuration, it says "High voltage...
Hello, I want to transmit data using the nRF52840 card and a smartphone. I explain: I must transmit data from the nRF52840 card to a smartphone. What is the best program in...
Hi,
I am trying to add logs to the Eddystone example using SDK15, SD132, arm5_no_packs, PCA10040 and Keil. I added the corresponding libraries to the project, entries...