Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
on NRF51 BLE peripheral I want to implement authentication, so only selected BLE masters have access to my BLE peripheral.
There is a password known to BLE peripheral...
Regarding the RTC prescaler of nRF51822,
I found out that it is the following.
Timer and RTC prescaler behavior by TASKS_CLEAR is different,
When TASKS_CLEAR is executed...
My company is making capacitive touch plates and to make them smart, app is used.We are using NRF24L01+ for rf communication between device and app. Our sockets and hub with...
I did some modification from radio test example.
But I don't know why the function "rand8" never ending.
In the function, rand8,
NRF_RNG->EVENTS_VALRDY = 0;
while (NRF_RNG...
Hi,
I have been trying to get up and running since the first DK was released for nRF52x and I am yet to have installed a working development environment. I have tried to...
I'd like to use a DMA channel on the nRF52 to copy RAM from one block to another. However, there doesn't appear to be any DMA controllers that are not directly associated...
Hello everyone
I'm trying to disable advertising but it doesn't work in some cases, I don't really know why. Here is my pretty simple piece of code:
/* Disconnect and...
www.keil.com/.../uv4_db_dbg_evr.htm
www.keil.com/.../EventRecorder.html
Keil worked in a new EventRecorder feature that uses some SWD buffer memory to push data out...
Hello,
A question to understand please. A lot of issues still unfixed in rev 1, but are known for a long time (see errata docs). Like SPI with RX = 1, DCDC -4dB on RF,...
Hello, I try to run the sdk example for adc, i set an input voltage in varying from 0 to 4.38 V in the pin 4 (AIN2), but the returned value didn't corresponds to the desired...
It there a specification for current draw during POR? (From time Vdd starts rising until cpu starts executing?) For nRF51 and 52.
I found this devzone.nordicsemi.com/....
(Hello! I'm drawing the module circuit base on nrf52832 with rfx2401 power amplifier (PA). As I understand it needs to set pins TXEN, RXEN to high level to activate this PA...
It may sound a bit old and you may have fixed them in latest Soft Device stacks however I wanted to share with you a couple of pairing issues we encountered with Soft Device...
i am using nrf52832 and programmed it with eclipse by blinky example.. now i have to debug the project , but when i debug the project with the configuration given in tutorial...
