Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
I posted recently ( https://devzone.nordicsemi.com/f/nordic-q-a/40381/interfacing-with-mcp4725-with-twi-registers ) and after editing the post, I can no longer access it ...
Hello, boss, I used twi read/write data from others device, I find a strange problem, When in no-blocking mode, mainly loop use "sd_app_evt_wait" TWI can't write data to others...
Hi, all. I have been going through the mesh examples and have been able to do the light switching, dimming etc examples and have used the RTT as well as physical buttons to...
Hello everyone,
My problem is the next one :
I bought a Nema 17 stepper motor (this one : https://www.pololu.com/product/2267 ) and it’s driver (this one : https://www...
It appears to be an error in the function signature `sd_ble_gatts_hvx()`.
Since the call is made via software interrupt, the const qualifier is cast away regardless.
So...
I am trying to implement the HAL interface for USB devices in Mbed for the nRF52840. Mbed is currently on nRF SDK14.2 so I may not have all the most recent bug fixes for the...
Hi,
I would like to run a different LWM2M client other than leshan LWM2M. Could you please answer me following questions:
i) Can i run any other LWM2M client written in...
Hello,
To improve the performance of SAADC, I would like to isolate the SAADC from the bad effect of DC/DC and RF.
I assume that SAADC has some noise because of DC/DC...
SDK 15.2's scanning module tries to connect to advertising peers that pass filter criteria when the nrf_ble_scan_init_t connect_if_match field is set true even when the advertisement...
Hi Forum!
I have to understand NRF52 chip for my job! I used to work with STM32 before. It has "Interrupt" (e.g when I receive one byte via SPI, It generates one "SPI_Rx_Interrupt...
Hi, all. I would like some serious help. I have three nRF52840 boards and have been running all the examples from the blinky to light switch/dimming. I am, however, stuck...
Hi,
could you please explain me what nrf52840_peripherals library (located in nrfx folder) is actually doing and what do the numbers next to the definitions mean ?
I see...
Hello everybody, As part of the evaluation of the nrf52840, I have made range measurements. In the course of this I was also concerned with the question to what extent the...
hi,
I am compiling nrf52840 light switch sample code in an embedded studio, I am getting the error as extern "C" {: Invalid argument, how to get out of this