Hey,
I just want to know if anybody sucessfully connected HDMI CEC (One-Wire bus) with the nRF52832.
I would be very grateful if anybody could share the library or give...
As the tittle,can anyone tell me how to save data to the flash with nRF51822 ? I use SDK9.0.0 and S110. before I turn off my machine, I want to save several parameters to...
I use example from SDK 13 ble_app_uart_c.
I changed uuid to my uuid from nrf51 peripherial device. I get event BLE_GAP_EVT_CONNECTED
where made
err_code = ble_db_discovery_start...
dear all,
i need your help.
Where we are:
We use mbed software developer platform.
We have BLE Nano V1.5 + MK20 USB Board V1.0 from RedBear.
We are able to generate...
Hi:
environment:
target board: DK52 board and run LWM2M example of IOT-SDK v0.9
router: ubuntu 16.04 on VM and runs bsserver and LWM2M server on ubuntu 16.04 ...
Hi,
I'm interfacing a nrf51822 and a H8/3294. My question is how much can I drain a the txd pin of the H8/3294. That means my question isn't really about nrf51822.
In documentation...
Hello everyone,
I would like to extend one of my program to use the new features of the BLE 5.0. It works in broadcast mode with BLE_GAP_ADV_TYPE_EXTENDED_NONCONNECTABLE_NONSCANNABLE_UNDIRECTED...
Hi Nordic,
I'm starting a project using the Thingy 52 and I'm going to connect Thingy with another sensor.
I have four communication options from the sensor:
UART, I2C...
Hello,
I'm using the buttonless DFU bootloader examples with bonding and the PC nrfutil with a nRF52840 PDK for the firmware upload.
If I try to start the DFU process...
I'm running SDK 14.0.0 and notice in the examples/flashwrite, the very last flash page is chosen as the place to write data to. Are there any caveats to that? WIll this location...
Hi, everyone. Long time no see.
I wonder if there is a free IDE which is official recommended. As we know that Keil and IAR are all commerical software. GCC command line...
Hello everyone,
As we know the proxy protocol is defined to include BLE devices in a mesh network. But as per my understanding there has to be made some changes in the...
Hello,
I am using nRF52840 PCA10056 DK i want to make my board as central device and scan for all nearby ble devices and display it's device id on terminal connected via...
Using SCAN_INTERVAL and SCAN_WINDOW at 1600 vill make the flash write and erase come out with a error, the fstorage is working fine before the SD is initialised.
/** @brief...
Hi,
I am using the secure bootloader as a template and I want to use the inactivity timeout to shutdown after 10 minutes.
I saw that the limit should be 60000000 ms (according...
SDK: nRF5 SDK for Thread and Zigbee 1.0.0
I have code for the SAADC based on the Low Power SAADC example here .
I have modified it to sample 4 inputs, and changed the...
Hi,
I would like to check battery level using the SAADC of the nrf52840.
Assuming the voltage is less than 3.6V, do I need to have a resistor between the battery and the...
HI,
I am new to IoS development with NRF.
I am having NRF52840 DK, IoS device. I want to implement USB HID device application (similar to pulse/Gluco meter ) on IOS. I...
Hi,
I am not able to compile the SDK example by using SES for ARM V3.52.
I got one error which shown below:
It pointed to the link ldr r0, =%4
Thanks
Gan
