Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
My nRF52840 Dongle appears to have failed while its boot loader was being updated, the led does not flash red like it used to and only gives a short white flash on plugging...
Hi, everyone,
We are developing the BLE project on nRF52832 chip by using RTT / UART logging. Previously we monitored the project via UART communication port. But than we...
Dear Team,
Can you please review the attached schematic of NRF51822 used with matching Balun and chip antenna.
Balun: 2450BM14E0003T
Chip Antenna: 2450AT18A100E...
I have an application running on an nRF52 with the S332 softdevice which is a server which exposes a a few services each with a few characteristics. I am using the Nordic...
Can the nRF2460 be operated with TXLAT (0x52) set to a value lower than 4 ?
Can the nRF2460 have a lower latency than 20mS ?
The range requirements are very small (30...
Hi All,
I have created a custom board header file based off of the pca10040.h file. I have customised this to support 10 buttons and 2 leds. I have also extended the array...
Hi everyone ;)
I have a problem with timeslot ESB library with Bluetooth LE. In my application i need do somethingh like that:
Bluetooth and ESB PRX works excelent...
Hi, I am using the BLE mesh 2.2.0 with nRF5_SDK_15.0.0_a53641a. I am using Segger embedded studio as toolchain. I was able to compile and flash the default app code onto NRF52...
I am working on an application to connect approximately 500 devices in a single network... trying to check if Thread or Mesh is a better option... Please do suggest...
After searching around a little bit I found this post, but sadly an answer did never come up apparently. I'm using the nrf52 DK, using the 132 Softdevice.
I'm kind of at...
Hi every one!
I have nRF52840 dongle and BMD-300 Series Evaluation kit featuring the nRF52832.
I`d like to transmit continuous signals from nRF52832 to dongle(Desktop...
I have two ble boards（board A and B）, one for client(Board A) and the other serve as slave(Board B). now i want to use board A to upgrade the application of board B by OTA...
Hi,
i would like to use the Power Profiler v2.0.0 from nRF Connect Software. The Power profiler is connected and it works with the Software 1.0.0. When i launch the power...
Hello,
I want to configure de coded mode on my nRF52DK, using the ble_app_interactive. How can I do it ?
I've saw that I can set the coded mode by de CENTRAL to a PEROPHERAL...
