Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
Hi guys,
I compiled the openbootloader example and when I try to run it on NRF52840, It gives segmentation fault:
(gdb) load nrf52840_xxaa_debug.hex Loading section .sec1...
Hi,
I'm having problem with the example code in the "Bluetooth low energy Services, a beginner's tutorial", the code was downloaded from github.
I'm using SES V3.5 for...
Hi,
We are currently develop our costum board with an nRF52840 SoC. Are the nRF52840 shipped with an initial bootloader to programm the device via USB? Because if possible...
Hello folks.
Easy question.
I want to add a .a static library to Segger Studio, but I don't know exactly where to add it. I know how to do in a Makefile with GCC, same...
I found the reference design files for nRF24LE1 from here ( https://www.nordicsemi.com/eng/nordic/download_resource/10898/2/41030525/1871 ), but I can't open them in EAGLE...
pca10059, replacing stock bootloader with Adafruit UF2, using USB dfu Hi. I currently don't have a J-Link at hand, so I tried to flash the UF2 bootloader using the stock DFU...
I want to keep both chip antenna and external antenna options on our board, what is best way to handle this for nRF24LE1 4×4mm QFN24 chip-set? Can I branch the Radio by having...
Hi,
I have a nRF52840 DK and a nRF52840 Dongle. I want to test to send binary data from one to each other using Bluetooth 5 or Nordic proprietary protocols. Are there...
Hi everyone, I am newcommer in here. I just buy one nRF52840 Dongle. I want to connect it with nRF52832 DK with ble_app_uart implemented; and open a COM port in MATLAB to...
Hi,
My application is based of ble_freertos_hrs example (SDK 14.2, nRF52832) and I need some variables to survive an assertion.
It appears that Keil has deprecated #pragma...
Hi Engineer： When I use nrf5_SDK_for_Mesh_v2.1 to debug the "light_switch" project, I always need to use a minimum of three boards (one as a provisioner, one as a client,...
I am using the nrf52832dk,i am working with the spi example for the sdk15,which pins are used for the spi protocol. I am enabling spim0.in sdk_config. h the pins number 3...
I am using NRF52832 as tags for asset tracking. I want to sense whether the asset is in movement or not as simple logical '0' or '1' response from sensor. Please suggest a...
I need sample code for the multiceiver mode. I want to send data from multiple NRF24LE1s as transmitter (to be exact 3 in number) to a single receiver. I read from the data...
