Hello,
I have a device based on nRF51822 revision 2 and SoftDevice S110 v7.1.0. Because it is revision 2 it is affected by PAN44 and PAN45, and by default the SoftDevice...
Hi Guys,
I know this is more for software issues. But I was curious as to where I can find trusted case providers/makers for the nrf51822 Beacon. Can anyone from the community...
Hi,
Has anyone converted the Adafruit graphics library for Arduino, Adafruit_GFX.h, to be compatible with the nRF51?
Could you please advise on how to convert this Arduino...
Hi all,
I have a few questions:
How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc...
The datasheet has "typical...
Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
Hi, Im trying to add multiple endpoint support to a zigbee project.
Im using the SDK for Zigbee 2.0 but in the documentation says:
" APIs for multiple endpoints A single...
Hi,
If you are using NRF52840, I am using SDK14.2 and Softdevice 5.0.0-2 version.
I want to update to SDK15.1, Softdevice 6.0.0 via USB bootloader DFU. Is it possible...
Dear All,
1. I'd like to know if below two lines which high-lighted in RED , Line width should be designed to provide 50 Ω impedance matching characteristics ?
...
About the data rate item of 5.4 Receiver Opetation in the data sheet of nRF24L01 +. Sensitibity is -82 dBm at 2 Mbps and -94 dBm at 250 kbps, is 250 kbps more susceptible...
Hi all.
I have a working multi-link central NUS project, and a working USB_CDC project for the nRF52840 SDK 15, nordic dev board.
I have merged the two as I need a USB...
Hi
I have a RGB LED and want to have bellow process for brightness:
Red from o to 100 then Green from 0 to 100 and Blue from 0 to 100.
till now i by bellow code i can...
Good afternoon,
I am currently using ble_app_hrs_rscs_relay example in the ble_central_and_peripherals part of the SDK. I am just testing out the example and trying to pair...
i am using the nrf52840 ble-uart development kit examples ( ble_app_uart_pca10056_s140 ), with an nrf52840 development tool board. Connected to a device that only accepts...
Hi All,
Currently, I am developing on nRF52840 and use nRF mesh application (android app)for provisioning and configuration.
So, for the publish and subscribe address...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
I am responsible for developing auxiliary logic in the nrf51822 and have run aground on an issue which I have not been able to find a solution to on my own so I am going to...
Hi,
I've finally managered to get pc-ble-driver (latest master branch) built and downloaded the connectivity firmware to the target, but now I met 2 issue which need help...
Hi, all, When I compile "light_switch_proxy_client_nrf52832_xxAA_s132_6_0_0" with SEEGER Embedded Studio, I got error: nrf_log.h: No such file or directory. I modified nothing...
I am using SDK15.2 with NRF52840-DK.
I want to use BLE5 long range Advertising features on NRF52840. and scan the advertisement on another side with a long distance seperated...
We have a system where the nRF52840 is running a cellular modem. We’re using the stock secure bootloader for DFU from a PC. However, we would like the option of updating over...
