Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
I have an external 32MHZ crystal on my custom board.I want to configure it to 32 MHZ external crystal to operate the chip. i changed the some register configuration in software...
all works fine with iphone that mean data stored, bond 's information that has been persisted during DFU processing.everything works with iphone. but when the device that...
Dear Nordic Team,
Thanks for supporting.
Now i want support for single channel(Ch 37) advertise , please support anyone. I am using ble_app_uart example.
My SDK : SDK12...
I'm running some stress tests on a nRF52832-based product, with the following setup:
- SDK 12.0.0
- SD 3.1.0
- Compatibility modes 1 and 2 enabled.
The device exposes...
hi ,
1. How do I migrate the codec OPUS part of SR3 ? I want to use it for audio. But migration always fails. Any migration examples?
2. How effective is ANR work? Are...
I use blinky_freertos demo on nrf52832,
now I want to disable FPU,
but when I disable FPU in Keil MDK option->Target Floating Point Hardware Not Used,
there is an error...
Hi,
i am using nrf52, sdk11 and S132v2.0.0. so i want to flash the hex file using OTA so that, i have create zip file using fallowing command.
**nrfutil dfu genpkg --application...
I've been trying to set up my nRF52 DK on my mac OS.
I followed all the steps to download the SDK (15.0.0), the Command Line Tools, the ARM GCC toolchain, and the J-Link...
Hi,
I have a few doubts regarding Subnet in Bluetooth mesh:
1) If a node including in 3 subnets, how it manages to switch between multiple subnets?
2) What are the various...
Hello,
I am using nRF52832, s132_nrf5.0.0_softdevice.
I am trying to build a ble gsm gateway.
I have 3 different peripheral devices. They have some services.
On my...
Hi
I am using SDK 14.2 secure bootloader with IAR and SES build. My IAR project is working with DFU upgradation but my SES Hex file is not working
Procedure Followed...
Hi, I use s132 and SDK15 to work with nrf52832. In code I set up RTC and CC to trigger every N ticks. It works as expected and time periods counted correctly. However, when...
Hi,
I can't find the whisper mode（-30dbm TX power） on nRF52832, which is available on nRF51822.
Does is have been disabled on on nRF52832?
Regards,
Aaron
