Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
I am using nRF5_SDK_11.0.0-2.alpha_bc3f6a0 with PCA10040 and GCC. I am working on the ble hrs with DFU example. I have modify the hrs to my custom service with a 128bit service...
Hello DevZone,
I know that the subject has already be treat but in the others posts people seems to say that the error comes from the double buffering.
But in my case...
I am using the sensors LIS2DH12 and the BMP280 in my new design, both of which work on SPI. i will be using both the nrf51822 and the nrf52832 in separate designs with same...
Hello folks,
I have a code that need variables of 267kb. It is just one part of the functionality of the total code.I'm using softdevice s132 for ble. I'm using nrf_malloc...
I have been modifying a project we have to use the s332 2.0.1 with SDK 12.1. Upfront, In the current project environment, I can't update the version of the SDK I'm using,...
Hi,
Using SDK 15, I' having the following issue:
My project works with USB and softdevice (among many other features)
1. I included the file nrfx_power_clock.c in my...
I plan on using MPU to mark all memory (SRAM) as XN. I would like to know if this could cause any issue with SoftDevice (iow, may the softdevice execute any code from SRAM...
The design I'm working on will tentatively use "Original SPI" (like "Original Coke" ...), so I started cutting up the QSPI bridges to disconnect DIO2 and DIO3 (which are also...
HI I have build the hex but it is not working it didn't provisioned using provision example in sdk2.2 and I noticed no led light up on device reset. Is it due to soft device...
Dear Sir,
I am trying to implement the following scenario. I am working on nrf52832 with SDK15 and soft device 6.0.0.
I have a peipheral device which is advertising for...
ruuvi is connected to ruuvi dev board to Nordic dev board connected to Mac book pro.
As usual
But
nrfjprog version: 9.7.3
JLinkARM.dll version: 6.33a
...
I am using Nrf52 DK as a J link programmer to program Laird BL-652 which is connected to NXP LPC 1519 via RX/TX Pins. I am trying to send commands from BL652 to NXP via UART...
Does anybody develop bluetooth JOYSTICK?
Could you please help me with some code samples to understand how to do Joystick on NRF products.
Best regards.
Hi
I am setting an interrupt off the RTC to cause wakeup from nrf_pwr_mgmt_run(); This is to conserve power. My code is working but the times are out by an order of magnitude...
