I am using nrf sniffer for trouble shooting. But it always exit unexpectedly. Wireshark was still open but the DOS window got closed.
I am attaching the log.txt.
log...
Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Good day, I am new to this forum so I am having some problems posting my question. Sorry for any inconveniences. I am having serious problems flashing my custom NRF5282 board...
I want to connect nRF52832 with PC. The objective is using nRF52832(I am using BT832 Module) I have to scan all Blue Tooth deceives details and send to PC. Please help with...
Hi,
I am using a custom board with the nrf52832 with SDK 13 and I have a bootloader and an application that both configure and feed the WDT.
However, upon restart (power...
Is there any straight forward way to detect jamming using any technique on this Nordic device? I'm using SDK 15.2, Soft-Device 6.1 Would this be possible by the new SD 6 function...
I have been using SMD modules with NRF24L01+ fitted.
The first batch I used worked fine for months.
Then I purchased another batch and found the tx_ds_active or max_rt_active...
Hi,
1. I went through the document. I'm trying the example applications Light-Switch on PCA10040 DK and NRF5 SDK for Mesh V2.2.0. So it is like the Client will be provisioned...
Good afternoon,
Following up my previous case, to which I got no reply, how can I use a queued write characteristic to write less than 20 bytes of data?
I'm using it...
I'm trying out Zephyr on the nRF52 DK, specifically I want to test the ADC drivers. Since things are moving quite fast in the Zephyr development world, there may be some information...
Hello, I'm working on Mesh SDK 2.1.1 and I'm trying to send a Relay Set message through Configuration Client. I have changed the code of models_init_cb() function inside the...
The nrfx_spim driver has an issue when chip select pin of the driver is not used.
When nrfx_spim_init is called with a nrfx_spim_config_t whose ss_pin is set to NRFX_SPIM_PIN_NOT_USED...
Dear Nordic
I have custom board(nRF52840) its not detecting through Jlink (from nRF52 DK).
I tried to connect nRF52840 dongle(using J2 in dongle) with same setup its detected...
Hi,
I am latest SDK 15.0, and using FDS library to store custom data. I have followed FDS examples but couldn't succeed in writing data to flash. When i tried to debug,...
Hi Guys,
We started to develop a mesh network with nRF52840 DK's and dongles. I have made some adjustments in the code with segger to use the server example of the led switch...
I just want to globally set the power level, and forget about it.
I have seen this post, and it still seems unclear how to do this - or if it's even possible.
Is there...
